Fujitsu 154V ユーザーズマニュアル
5. CIRCUIT DESCRIPTION
5-1 MICRO CIRCUIT
IC101 is CPU, This CPU has the following functions.
1. Detect timing mode by sensing the horizontal frequency, vertical frequency, the polarity of Hor. Sync and Ver. Sync.
2. Key board scan control.
3. Cs capacitor switch control.
4. Power saving control.
When CPU detects timing, it takes data from E²PROM (IC102), then output voltage to control the geometry of this monitor.
If key is pressed, the CPU will do some job according to the key function. For example, if function key is pressed, it can change different
value to control screen geometry (H-SIZE, V-SIZE...etc.)
value to control screen geometry (H-SIZE, V-SIZE...etc.)
5-2 DEFLECTION CIRCUIT
Hor. sync. and ver. sync., come from PC, go into the CPU (IC101). The output goes to the Hor. oscillation and Ver. oscillation processor
(IC401). The IC401 treats sync. signal and output the drive signal to horizontal and vertical output circuit. IC401 also generates some
functions for geometry use, like, horizontal center, vertical size, by I²C bus control, the geometry can be controlled. IC601 is a vertical
output IC to supply the vertical scan. Q404, Q405, Q406 and L405 are the horizontal size controls. Q403 is the horizontal deflection
output, supply the horizontal scan of the monitor. Q707 and Q601 generate the Blanking signal output to G1 of CRT.
(IC401). The IC401 treats sync. signal and output the drive signal to horizontal and vertical output circuit. IC401 also generates some
functions for geometry use, like, horizontal center, vertical size, by I²C bus control, the geometry can be controlled. IC601 is a vertical
output IC to supply the vertical scan. Q404, Q405, Q406 and L405 are the horizontal size controls. Q403 is the horizontal deflection
output, supply the horizontal scan of the monitor. Q707 and Q601 generate the Blanking signal output to G1 of CRT.
Q703 Q704 and Q705 are mute control, brightness control and G1 DC voltage output.
5-3 VIDEO CIRCUIT
IC801 is a video amplifier, clamping signal input from pin No. 11 to restore the DC voltage of video signal, the signal output from IC801
pass through IC802 video package amplifier stage LM2438, then go to the cut off DC restore stage, The video output signal is about
40Vpp.
pass through IC802 video package amplifier stage LM2438, then go to the cut off DC restore stage, The video output signal is about
40Vpp.
5-4 POWER SUPPLY
The design uses a discontinuous flyback topology operating in current-mode resulting in a multiple output switcher with stack well. Faster
diodes are used. The fast transient response of the control loop maintains picture integrity. Very fast current limiting protects the switcher
agains short circuits.
diodes are used. The fast transient response of the control loop maintains picture integrity. Very fast current limiting protects the switcher
agains short circuits.
UC3842AM (IC901) is the current mode controller selected. It offers feed forward compensation, feedback error amplifier, and low
voltage lock out features. The 3842 draws very little current is start up mode. There is enough power from the line bleeder to slowly charge
a capacitor to the 16 volts needed to start the switcher.
voltage lock out features. The 3842 draws very little current is start up mode. There is enough power from the line bleeder to slowly charge
a capacitor to the 16 volts needed to start the switcher.
The FET starts a cycle by allowing current to flow into the primary of the power transformer. As current ramps up with time, the voltage
across the current sense resistor (R929) also ramps to a point where the 3842 determines that enough power is stored and turns off the FET.
As the voltage on the transformer reverses, power is dumped from the main power transformer through diodes into the different supplies.
To keep RFI to a minimum and reduce transistor heating, a turn-off snubber network is placed across the FET. Current from the secondary
windings are rectified and filtered to freate the desired voltages. Small high current capacitors quickly return charging current to the source.
Filter inductors remove high frequency noise.
across the current sense resistor (R929) also ramps to a point where the 3842 determines that enough power is stored and turns off the FET.
As the voltage on the transformer reverses, power is dumped from the main power transformer through diodes into the different supplies.
To keep RFI to a minimum and reduce transistor heating, a turn-off snubber network is placed across the FET. Current from the secondary
windings are rectified and filtered to freate the desired voltages. Small high current capacitors quickly return charging current to the source.
Filter inductors remove high frequency noise.
Page 10 of 59
4V SERIES MANUAL
05.06.2002
file://D:\PC%20AOC\SERVICE%20MANUAL\FSC\154V\154V-C551.htm