Fujitsu P65FT00AEB ユーザーズマニュアル

(1) You can make to the standby state automatically when the 

no signal state continued during set up time.

Press 

a

 or 

b

 to select the “Time”.

Press 

c

 or 

d

 to select the amount of time before the 

standby state starts.

<

 Off < 1 min. < 15 min. < 45 min. < 60 min. <

Press 

Z

 to store.

*  The numerical value is the approximate amount of time 

before the standby state starts. 

(2) You can assign the black or white color for the background 

color at the no signal state.
Press 

a

 or 

b

 to select the “Background”.

Press 

c

 or 

d

 to select the displayed background displayed.

<

 Black < White <

Press 

Z

 to store.

* The background color changes to assigned color state 

after approximate 20 seconds at the no signal state.

Saves Digital Tuner power consumption when watching analog 
TV, video input, and RGB input other than digital terrestrial 
TV (DTV).
Normally, when digital terrestrial TV (DTV) is watched very 
little and analog TV and cable TV and DVD player are 
watched by video input very much, setting to ON is 
recommended.
Each time you press 

c

 or 

d

, the setting is switched.

<

 Off < On <

[Off]: Power consumption not saved.
[On]: Power consumption saved.
* When set to On, it may take some time to switch to 

digital terrestrial TV.

You can use this option to select the available terminals to 
receive the audio from input equipment.
(1) Press 

a

 or 

b

 to select video input terminal.

(2) Select a related audio input terminal.

Each time you press 

c

 or 

d

, one of the available choices 

appears in the following sequence:

<

 No Audio < Audio1 < Audio2 < •  •  •  •  • <

[No Audio]: No audio in the corresponding mode.

[Audio 1-2]: SCART
[Audio 3-4]: Selects Audio 3 through 4 for receiving 

audio in the corresponding mode.

[Audio 5-6]: HDMI
* There is also “Audio Input” that cannot be selected. 
* Repeat steps (1) and (2) for each piece of input 

equipment.

(3) Press 

Z

 to store.

* AUDIO menu will not be displayed when “No Audio” is 

selected.

You can use this option to move the screen position to 
minimize phosphor-induced “burn-in”.
Follow the steps below.

(1) Select “Screen Orbiter” and press 

Z

.

The “Screen Orbiter” setting screen will appear.

(2) Press 

a

 or 

b

 to select “Mode/Time”.

(3) Select a desired pattern.

Each time you press 

c

 or 

d

, one of the available choices 

appears in the following sequence:

<

 Off < Time < Mode < 

[Off]: Disables Screen Orbiter.
[Time]: Moves the pattern approximately every one hour.
[Mode]: Moves the pattern when the power is turned ON 

or when you switch between modes.

(4) Press 

a

 or 

b

 to select “Moving Area”.

(5) Press 

c

 or 

d

 to select the range for moving the pattern.

Each time you press 

c

 or 

d

, one of the available choices 

appears in the following sequence:

<

 Min. < Std. < Max. < 

[Min.]: Pattern moves in small range. (About 5 pixels)
[Std.]: Pattern moves in moderate range. (About 10 pixels)
[Max.]: Pattern moves in wide range. (About 15 pixels)

(6) Press 

Z

 to store.

* When the Screen Orbiter function is operated, some 

screen contents at the top, bottom, right or left of the 
screen may move offscreen.

“Auto Off-NO SIG.” selection screen

“Audio Input” settings screen

“Screen Orbiter” setting screen

7701_01_E.book  36 ページ  ２００７年３月２２日　木曜日　午後２時３８分