Campbell Manufacturing R410 ユーザーズマニュアル
G-1
Appendix G. Short-Haul Modems
Set SRM-5A at PC end to “DCE” mode.
Set SRM-5A at RF400 end to “DTE” mode.
Set SRM-5A at RF400 end to “DTE” mode.
The PC to SRM-5A cable is typically a 9-pin female to 25-pin male (CSI Item
# 7026). The SRM-5A to RF400 cable is 25-pin male to 9-pin male available
as CSI Item # 14413.
# 7026). The SRM-5A to RF400 cable is 25-pin male to 9-pin male available
as CSI Item # 14413.
LoggerNet or PC208W Network Map:
COM1
CR10X1
RCV
--
+G
+
XMT
DTE
DTE
DCE
DCE
RCV
--
+G
+
XMT
DTE
DTE
DCE
DCE
RS232
DC
Pwr
CS I/O
Pwr/TX
RX
MADE IN USA
Serial #
Program
Antenna
14320
RF400
Spread Spectrum Radio
This device contains transmitter module:
FCC ID: OUR-9XTREAM
The enclosed device complies with Part 15 of the
FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any intererence
received, including interference that may cause
undesired operation.
Logan, Utah
SE
DIFF
DIFF
G
G
H
L
1
2
1
AG H
L
AG H
L
AG E1
AG E2 G
3
4
2
5
6
3
SE
DIFF
DIFF
G
G
H
L
7
8
4
AG H
L
AG H
L
AG E3
AG G
G
9
10
5
11
12
6
P1 G
P2
G
C8 C7 C6 C5 C4 C3 C2 C1
G
12V 12V
SDM
5V 5V G
G
SW 12V
SW 12V CTRL
Logan, Utah
G
12V
G 12V
POWER
IN
IN
CR10X WIRING PANEL
MADE IN USA
WIRING
PANEL NO.
PANEL NO.
EARTH
GROUND
GROUND
CS I/O
apx
TECHNOLOGIES INC.
CLASS 2 TRANSFORMER
MODEL NO:
MODEL NO:
AP2105W
INPUT:
120VAC 60Hz 20W
LISTED
2H56
E144634
2H56
E144634
MADE IN CHINA
OUTPUT:
12VDC 1.0A
HICKSVILLE, NEW YORK
UL
R
UL
R
RS232
DC
Pwr
CS I/O
Pwr/TX
RX
MADE IN USA
Serial #
Program
Antenna
14320
RF400
Spread Spectrum Radio
This device contains transmitter module:
FCC ID: OUR-9XTREAM
The enclosed device complies with Part 15 of the
FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any intererence
received, including interference that may cause
undesired operation.
Logan, Utah
FIGURE G-1. Short-Haul Modem to RF400 Setup
Configure RF400s for point-to-point (see Software Setup Section 5.3). Default
settings should work unless there is a neighboring network (see Section 5.3.1,
4.d).
settings should work unless there is a neighboring network (see Section 5.3.1,
4.d).
12 V power for the base RF400 can be supplied by an AC adapter as shown or
a Field Power Cable (see Power Supplies in Section 4.4). Current dataloggers
will supply remote RF400 power via serial cable.
a Field Power Cable (see Power Supplies in Section 4.4). Current dataloggers
will supply remote RF400 power via serial cable.
SRM-5A Short-haul Modems
Datalogger CS I/O
CS I/O
DCE
DTE
RS-232
AC Adapter