ONKYO ABX-N300 ユーザーズマニュアル
En-
22
Rocketboost™ (North American models only)
—Continued
Initial Rocketboost Setup
Insert the WLC-TR1 into the Rocketboost Module Slot
on the back of the ABX-N300.
on the back of the ABX-N300.
Note:
The ABX-N300 must be in standby mode when you
attach the Rocketboost Wireless Card (WLC-TR1, sold
separately). If the ABX-N300 is powered-on, press the
[] button to put it in standby mode.
The ABX-N300 must be in standby mode when you
attach the Rocketboost Wireless Card (WLC-TR1, sold
separately). If the ABX-N300 is powered-on, press the
[] button to put it in standby mode.
Pairing
Rocketboost products form an audio network. Every
Rocketboost network must contain one hub device,
which helps devices join the network. To add the
ABX-N300 to your Rocketboost network, you need to
pair it with your hub device.
Rocketboost network must contain one hub device,
which helps devices join the network. To add the
ABX-N300 to your Rocketboost network, you need to
pair it with your hub device.
1
Insert the Rocketboost Wireless Card
(WLC-TR1, sold separately) to the
ABX-N300.
(WLC-TR1, sold separately) to the
ABX-N300.
Take care that the connector is oriented correctly,
and insert it all the way.
and insert it all the way.
2
Power-on the ABX-N300, and set the input
to “Rocketboost.”
to “Rocketboost.”
Use the ABX-N300’s [INPUT] button or the
remote controller’s INPUT []/[] buttons to
select “Rocketboost.”
remote controller’s INPUT []/[] buttons to
select “Rocketboost.”
3
Refer to the owner’s manual for your hub
device for the relevant pairing information,
then pair the ABX-N300 with the hub device.
device for the relevant pairing information,
then pair the ABX-N300 with the hub device.
4
Hold down the [] button on the ABX-N300
until the Status indicator of the
Rocketboost Wireless Card (WLC-TR1, sold
separately) is lit.
until the Status indicator of the
Rocketboost Wireless Card (WLC-TR1, sold
separately) is lit.
While pairing is occurring, the display will indicate
“Pairing” and the Status indicator will blink.
“Pairing” and the Status indicator will blink.
Reception will begin when the Status indicator has
changed from blinking to steadily lit, and pairing
has been completed.
changed from blinking to steadily lit, and pairing
has been completed.
When pairing is complete, the ABX-N300 is now
part of your Rocketboost wireless network and it
can receive audio from other Rocketboost sender
devices. The Rocketboost network can include a
total of nine devices (any combination of sender
and receiver devices). The maximum number of
wireless audio stream being sent over the network
at the same time is five.
part of your Rocketboost wireless network and it
can receive audio from other Rocketboost sender
devices. The Rocketboost network can include a
total of nine devices (any combination of sender
and receiver devices). The maximum number of
wireless audio stream being sent over the network
at the same time is five.
5
Turn on the audio source connected to the
Rocketboost wireless sender.
Rocketboost wireless sender.
Make sure the volume of the audio source is turned
up and not muted, otherwise no audio will be sent
over the Rocketboost network. You can also adjust
the volume level at the ABX-N300.
up and not muted, otherwise no audio will be sent
over the Rocketboost network. You can also adjust
the volume level at the ABX-N300.
Tips:
If you have multiple audio sources in your Rocketboost
network, press the [/] button to hear the next audio
source. Press the [/] button again to cycle through all
available audio sources.
If you have multiple audio sources in your Rocketboost
network, press the [/] button to hear the next audio
source. Press the [/] button again to cycle through all
available audio sources.
Rocketboost Setup