Omnitron Systems Technology 4385 ユーザーズマニュアル
2
Omnitron Systems Technology, Inc.
It is very strongly recommended that a replacement power supply unit be installed
as soon as possible in order to prevent overheating of the chassis unit.
as soon as possible in order to prevent overheating of the chassis unit.
THE POWER SUPPLIES ARE HOT-SWAPPABLE AND CAN BE REPLACED
WITHOUT SHUTTING THE NETWORK DOWN. HOWEVER, WHEN REMOVING AND
REPLACING A POWER SUPPLY UNIT, THE FOLLOWING STEPS MUST BE STRICTLY
FOLLOWED IN ORDER TO PREVENT SERIOUS INJURY OR DEATH, OR SERIOUS
DAMAGE TO YOUR EQUIPMENT.
WITHOUT SHUTTING THE NETWORK DOWN. HOWEVER, WHEN REMOVING AND
REPLACING A POWER SUPPLY UNIT, THE FOLLOWING STEPS MUST BE STRICTLY
FOLLOWED IN ORDER TO PREVENT SERIOUS INJURY OR DEATH, OR SERIOUS
DAMAGE TO YOUR EQUIPMENT.
Hot Removal of Power Supplies:
1. Determine which power supply needs replacing by observing the LEDs in the
1. Determine which power supply needs replacing by observing the LEDs in the
front left of the chassis: the top LED indicates the power status of the right
power supply (as observed from the front), the bottom LED indicates the
power status of the left power supply (as observed from the front).
Notice that LED being ON indicates that the power supply is operational. The
LED being OFF may indicate that the DC power is not applied, please verify
that your DC power source is providing power.
power supply (as observed from the front), the bottom LED indicates the
power status of the left power supply (as observed from the front).
Notice that LED being ON indicates that the power supply is operational. The
LED being OFF may indicate that the DC power is not applied, please verify
that your DC power source is providing power.
2. Once you determine that your DC source is connected properly, and the power
supply LED is still not ON, determine which is the failing power supply unit
and proceed to the next step.
and proceed to the next step.
3. Locate the 48VDC circuit breaker, and switch the circuit breaker to the OFF
position.
4. Remove the DC power cables of the faulty power supply from the FlexPoint
power supply unit.
5. Loosen the 2 screws securing the power supply to the main chassis (observe
the illustration above).
6. Remove the faulty power supply.
7
Power Supply Mounting Screws
and guide pins.
(2 each per unit)
and guide pins.
(2 each per unit)
Power Supply Mounting Screws
and guide pins.
(2 each per unit)
and guide pins.
(2 each per unit)
48 V
DC
DC Power Input
48 VDC
Present
5 VDC
ON
OFF
OFF
48 V
DC
DC Power Input
48 VDC
Present
5 VDC
ON
OFF
OFF
48 V
DC
DC Power Input
48 VDC
Present
5 VDC
ON
OFF
OFF
Safety Considerations
Warning
The operating description in this Instruction Manual is for use by qualified personnel only. To
avoid electrical shock, do not perform any servicing of this unit other than that contained in
the operating instructions, unless you are qualified and certified to do so by Omnitron Systems
Technology, Inc.
avoid electrical shock, do not perform any servicing of this unit other than that contained in
the operating instructions, unless you are qualified and certified to do so by Omnitron Systems
Technology, Inc.
Caution
All user-required operations can be performed without opening the unit. Never attempt to
open or remove the cover or tamper with the unit or tamper with the power supply module.
open or remove the cover or tamper with the unit or tamper with the power supply module.
Warranty
This product is warranted to the original purchaser against defects in material and workmanship
for a period of TWO YEARS from the date of shipment. A LIFETIME warranty may be obtained
by the original purchaser by REGISTERING this product with Omnitron within 90 days from
the date of shipment. TO REGISTER, COMPLETE AND MAIL OR FAX THE REGISTRATION
FORM INCLUDED WITH THIS INSTRUCTION MANUAL TO THE INDICATED ADDRESS.
Or you may register your product on the Internet at http://www.omnitron-systems.com. During
the warranty period, Omnitron will, at its option, repair or replace a product which is proven to
be defective.
for a period of TWO YEARS from the date of shipment. A LIFETIME warranty may be obtained
by the original purchaser by REGISTERING this product with Omnitron within 90 days from
the date of shipment. TO REGISTER, COMPLETE AND MAIL OR FAX THE REGISTRATION
FORM INCLUDED WITH THIS INSTRUCTION MANUAL TO THE INDICATED ADDRESS.
Or you may register your product on the Internet at http://www.omnitron-systems.com. During
the warranty period, Omnitron will, at its option, repair or replace a product which is proven to
be defective.
For warranty service, the product must be sent to an Omnitron designated facility, at Buyer’s
expense. Omnitron will pay the shipping charge to return the product to Buyer’s designated
US address using Omnitron’s standard shipping method.
expense. Omnitron will pay the shipping charge to return the product to Buyer’s designated
US address using Omnitron’s standard shipping method.
Limitation of Warranty
The foregoing warranty shall not apply to defects resulting from improper or inadequate use
and/or maintenance of the equipment by Buyer, Buyer-supplied equipment, Buyer-supplied
interfacing, unauthorized modifications or tampering with equipment (including removal of
equipment cover by personnel not specifically authorized and certified by Omnitron), or misuse,
or operating outside the environmental specification of the product (including but not limited
to voltage, ambient temperature, radiation, unusual dust, etc.), or improper site preparation
or maintenance.
and/or maintenance of the equipment by Buyer, Buyer-supplied equipment, Buyer-supplied
interfacing, unauthorized modifications or tampering with equipment (including removal of
equipment cover by personnel not specifically authorized and certified by Omnitron), or misuse,
or operating outside the environmental specification of the product (including but not limited
to voltage, ambient temperature, radiation, unusual dust, etc.), or improper site preparation
or maintenance.
No other warranty is expressed or implied. Omnitron specifically disclaims the implied
warranties of merchantability and fitness for any particular purpose.
warranties of merchantability and fitness for any particular purpose.
Exclusive Remedies
The remedies provided herein are the Buyer’s sole and exclusive remedies. Omnitron shall
not be liable for any direct, indirect, special, incidental, or consequential damages, whether
based on contract, tort, or any legal theory.
not be liable for any direct, indirect, special, incidental, or consequential damages, whether
based on contract, tort, or any legal theory.