Omnitron Systems Technology 10FL/2 プリント

Please complete both sides and mail or fax this form to the address indicated on

the other side.

FlexPoint T

ype: 

 

 10FL/T

     

 10FL/2    

 

10T/2    

 Othe

r_____

Model:

_________________________________________________

Serial Number: ______________  

 Purchase 

Date:

______________

Purchased From: _________________________________________

Address:

______________________________________________

City:  ___________________  S

tate: 

 _______  

Zip Code:

________

Country:

_______________________________________________

Comments and 

Suggestions:

_______________________________

______________________________________________________

______________________________________________________

Please complete both sides of this form

“Termination” Switch:  When attaching anywhere along
a coax cable except at the end, the Termination Switch
should be set to “Termination Out” (factory setting). When
attaching to the end of a cable, it can be set to
“Termination In.”  Note that when the switch is set to
“Termination In,” an external termination element must
not be attached.

Power On

Yellow Power applied

Jabber

Red

Jabber condition

Fiber Link

Green Operational device detected at

the far end of fiber.

Fiber Rx

Green Received data on fiber line.

Coax Rx

Green Received data on coax line.

Collision

Yellow Collision detected

If you encounter problems in installing or maintaining
this product, contact Omnitron Technical Support:
Phone:

(949) 250-6510

Fax:

(949) 250-6514

Address:

Omnitron Systems Technology, Inc.
140 Technology Drive, #500
Irvine, CA 92618 USA

E-mail:

support@omnitron-systems.com

URL:

http://www.omnitron-systems.com

1. When using in a stand-alone configuration, this product
is intended to be used and must be used only with a
Listed Direct Plug-In Power Unit marked “Class 2” and
rated at 9Vdc, 1 Amp.

2. This product should always be used only with Omnitron
Supplied Power Unit model number 9113-PS.

The Omnitron FlexPoint 10FL/2 can be solo-mounted using
a wall-mounting kit, or rack-mounted using a 5-position space-
saver shelf, FlexRack 5, or a 14-position high-density
FlexPoint Powered Chassis.  When wall-mounting or shelf-
mounting, connect the power adapter unit.

When connecting the FlexPoint 10FL/2 at the end of a coax
segment, attach the coax cable directly into the FlexPoint’s
BNC coax connector.  When connecting it along the coax
line (not at the end), use a “T” connector to tap into the cable.

Attach the fiber cables to the FlexPoint’s connectors.  The
FlexPoint’s transmit (Tx) must attach to the receive side on
the device at the far end of the fiber and the receive (Rx)
must attach to the transmit side.

The FlexPoint

TM

 family of converters supports the

IEEE 802.3 and Ethernet Versions 1.0 / 2.0 standards.
They convert among 10BASE-FL fiber, 10BASE-2
thin coax and 10BASE-T twisted pair (UTP) media
types.

The FlexPoint 10FL/2 converts from 10BASE-FL fiber
to 10BASE-2 coax.  It uses ST fiber and BNC coax
connector.  The following models are described here:

4310

850 nm (multimode)

2 km

4311

1310 nm (single-mode)

30  km

4312

1310 nm (multimode)

5  km

The 10FL/2 provides a switch-selectable 50 ohm
termination that allows easy termination of the coax
cable.  This function should be used only when the
FlexPoint is connected at the end of a segment.

Note that the total length of the coax cable must not
exceed 185 meters and the number of stations on the
coax segment must not exceed 30 stations (per IEEE
802.3 specification).

Please complete both sides and mail or fax this registration form to:

Name:

_________________________________________________

Company:

______________________________________________

Adress:_________________________________________________

             ________________________________________________

City:  ___________________  S

tate:  _______  Zip Code: __________

Country:________________________________________________

Phone:  ____________________  Fax:________________________

E-mail:

________________________________________________

Please complete both sides of this form

The operating description in this Instruction Manual is
for use by qualified personnel only.  To avoid electrical
shock, do not perform any servicing of this unit other
than that contained in the operating instructions, unless
you are qualified and certified to do so by Omnitron
Systems Technology, Inc.

All user-required operations can be performed without
opening the unit. Never attempt to open or remove the
cover or tamper with the unit.

This product is warranted to the original purchaser
against defects in material and workmanship for a period
of TWO YEARS from the date of shipment.  A LIFETIME
warranty may be obtained by the original purchaser by
REGISTERING this product with Omnitron within 90 days
from the date of shipment. TO REGISTER, COMPLETE
AND MAIL OR FAX THE REGISTRATION PORTION OF
THIS INSTRUCTION MANUAL TO THE INDICATED
ADDRESS.  During the warranty period, Omnitron will,
at its option, repair or replace a product which is proven
to be defective.

For warranty service, the product must be sent to an
Omnitron designated facility, at Buyer’s expense.
Omnitron will pay the shipping charge to return the

product to Buyer’s designated US address using
Omnitron’s standard shipping method.

The foregoing warranty shall not apply to defects
resulting from improper or inadequate use and/or
maintenance of the equipment by Buyer, Buyer-supplied
equipment, Buyer-supplied interfacing, unauthorized
modifications or tampering with equipment (including
removal of equipment cover by personnel not
specifically authorized and certified by Omnitron), or
misuse, or operating outside the environmental
specification of the product (including but not limited to
voltage, ambient temperature, radiation, unusual dust,
etc.), or improper site preparation or maintenance.

No other warranty is expressed or implied.  Omnitron
specifically disclaims the implied warranties of
merchantability and fitness for any particular purpose.

The remedies provided herein are the Buyer’s sole and
exclusive remedies. Omnitron shall not be liable for any
direct, indirect, special, incidental, or consequential
damages, whether based on contract, tort, or any legal
theory.

Form:040-04310-001C  11/07

____________________________
____________________________
____________________________
____________________________
____________________________
____________________________
____________________________
____________________________
____________________________
_____________________________
____________________________
____________________________
____________________________
____________________________
____________________________
____________________________