Nxp Semiconductors UM10237 ユーザーズマニュアル
UM10237_2
© NXP B.V. 2008. All rights reserved.
User manual
Rev. 02 — 19 December 2008
645 of 792
NXP Semiconductors
UM10237
Chapter 25: LPC24XX Pulse Width Modulator PWM0/PWM1
6.7 PWM Latch Enable Register (PWM0LER - 0xE001 4050 and PWM1LER
0xE001 8050)
The PWM Latch Enable registers are used to control the update of the PWM Match
registers when they are used for PWM generation. When software writes to the location of
a PWM Match register while the Timer is in PWM mode, the value is actually held in a
shadow register and not used immediately.
registers when they are used for PWM generation. When software writes to the location of
a PWM Match register while the Timer is in PWM mode, the value is actually held in a
shadow register and not used immediately.
When a PWM Match 0 event occurs (normally also resetting the timer in PWM mode), the
contents of shadow registers will be transferred to the actual Match registers if the
corresponding bit in the Latch Enable register has been set. At that point, the new values
will take effect and determine the course of the next PWM cycle. Once the transfer of new
values has taken place, all bits of the LER are automatically cleared. Until the
corresponding bit in the PWMLER is set and a PWM Match 0 event occurs, any value
written to the PWM Match registers has no effect on PWM operation.
contents of shadow registers will be transferred to the actual Match registers if the
corresponding bit in the Latch Enable register has been set. At that point, the new values
will take effect and determine the course of the next PWM cycle. Once the transfer of new
values has taken place, all bits of the LER are automatically cleared. Until the
corresponding bit in the PWMLER is set and a PWM Match 0 event occurs, any value
written to the PWM Match registers has no effect on PWM operation.
For example, if PWM is configured for double edge operation and is currently running, a
typical sequence of events for changing the timing would be:
typical sequence of events for changing the timing would be:
•
Write a new value to the PWM Match1 register.
•
Write a new value to the PWM Match2 register.
•
Write to the PWMLER, setting bits 1 and 2 at the same time.
•
The altered values will become effective at the next reset of the timer (when a PWM
Match 0 event occurs).
Match 0 event occurs).
The order of writing the two PWM Match registers is not important, since neither value will
be used until after the write to PWMLER. This insures that both values go into effect at the
same time, if that is required. A single value may be altered in the same way if needed.
be used until after the write to PWMLER. This insures that both values go into effect at the
same time, if that is required. A single value may be altered in the same way if needed.
Table 564: PWM Latch Enable Register (PWM0LER - address 0xE001 4050 and PWM1LER
address 0xE001 8050) bit description
Bit Symbol
Description
Reset
Value
Value
0
Enable PWM
Match 0 Latch
Match 0 Latch
PWM MR0 register update control. Writing a one to this bit allows
the last value written to the PWM Match Register 0 to be become
effective when the timer is next reset by a PWM Match event. See
the last value written to the PWM Match Register 0 to be become
effective when the timer is next reset by a PWM Match event. See
0
1
Enable PWM
Match 1 Latch
Match 1 Latch
PWM MR1 register update control. See bit 0 for details.
0
2
Enable PWM
Match 2 Latch
Match 2 Latch
PWM MR2 register update control. See bit 0 for details.
0
3
Enable PWM
Match 3 Latch
Match 3 Latch
PWM MR3 register update control. See bit 0 for details.
0
4
Enable PWM
Match 4 Latch
Match 4 Latch
PWM MR4 register update control. See bit 0 for details.
0