Mitsubishi Electronics Q64TCTTN ユーザーズマニュアル
418
INDEX
A
Accuracy
Adjustment after auto tuning
Air cooled
Alarm code list
Alarm priorities
Alert dead band
Alert dead band setting (Un\G164)
Alert mode and settings
Alert mode and the set value (SV) to be referred
Alert with standby
Alert with standby (second time)
Algorithm of PID control in process-value incomplete
derivation
derivation
ALM LED
Applicable CPU modules and base units
Applicable software packages
Applicable solderless terminal
Applicable wire size
AT point
AT simultaneous temperature rise parameter calculation
completion
completion
AT simultaneous temperature rise parameter calculation
error status
error status
Auto refresh
Auto tuning
Auto-setting at input range change
B
Backup of the calculated value on completion of auto
tuning
tuning
Base unit
Batch/individual setting for temperature rise and
temperature drop
temperature drop
Buffer memory address by control mode
Buffer memory address for error history
Buffer memory areas related to auto tuning
Buffer memory areas related to control method
Buffer memory areas that can be saved and restored
Buffer memory areas that can be set only in the setting
mode
mode
Buffer memory assignment list
C
Calculation formula for heater disconnection
compensation
compensation
Checking the completion of auto tuning
CH Adjustment sensitivity (dead band) setting
(Un\G46, Un\G78, Un\G110, Un\G142)
(Un\G46, Un\G78, Un\G110, Un\G142)
CH Alert 1 mode setting (Un\G192, Un\G208,
Un\G224, Un\G240)
Un\G224, Un\G240)
CH Alert 2 mode setting (Un\G193, Un\G209,
Un\G225, Un\G241)
Un\G225, Un\G241)
CH Alert 3 mode setting (Un\G194, Un\G210,
Un\G226, Un\G242)
Un\G226, Un\G242)
CH Alert 4 mode setting (Un\G195, Un\G211,
Un\G227, Un\G243)
Un\G227, Un\G243)
CH Alert definition (Un\G5 to Un\G8)
CH Alert occurrence flag (XnC to XnF)
CH Alert set value 1 (Un\G38, Un\G70, Un\G102,
Un\G134)
Un\G134)
CH Alert set value 2 (Un\G39, Un\G71, Un\G103,
Un\G135)
Un\G135)
CH Alert set value 3 (Un\G40, Un\G72, Un\G104,
Un\G136)
Un\G136)
CH Alert set value 4 (Un\G41, Un\G73, Un\G105,
Un\G137)
Un\G137)
CH AT bias setting (Un\G53, Un\G85, Un\G117,
Un\G149)
Un\G149)
CH AT simultaneous temperature rise parameter
calculation flag (Un\G573, Un\G605, Un\G637, Un\G669)
calculation flag (Un\G573, Un\G605, Un\G637, Un\G669)
CH Auto tuning instruction (Yn4 to Yn7)
CH Auto tuning mode selection (Un\G184 to Un\G187)
CH Auto tuning status (Xn4 to Xn7)
CH AUTO/MAN mode shift (Un\G50, Un\G82,
Un\G114, Un\G146)
Un\G114, Un\G146)
CH Automatic backup setting after auto tuning of PID
constants (Un\G63, Un\G95, Un\G127, Un\G159)
constants (Un\G63, Un\G95, Un\G127, Un\G159)
CH Control output cycle setting (Un\G47, Un\G79,
Un\G111, Un\G143)
Un\G111, Un\G143)
CH Control response parameter (Un\G49, Un\G81,
Un\G113, Un\G145)
Un\G113, Un\G145)
CH Cooling control output cycle setting (Un\G722,
Un\G738, Un\G754, Un\G770)
Un\G738, Un\G754, Un\G770)
CH Cooling proportional band (Pc) setting (Un\G720,
Un\G736, Un\G752, Un\G768)
Un\G736, Un\G752, Un\G768)
CH Cooling transistor output flag (Un\G712 to
Un\G715)
Un\G715)
CH Cooling upper limit output limiter (Un\G721,
Un\G737, Un\G753, Un\G769)
Un\G737, Un\G753, Un\G769)
CH Decimal point position (Un\G1 to Un\G4)
CH Derivative action selection (Un\G729, Un\G745,
Un\G761, Un\G777)
Un\G761, Un\G777)
CH Derivative time (D) setting (Un\G37, Un\G69,
Un\G101, Un\G133)
Un\G101, Un\G133)
CH E
2
PROM’s PID constants read instruction
(Un\G62, Un\G94, Un\G126, Un\G158)
CH Forward/reverse action setting (Un\G54, Un\G86,
Un\G118, Un\G150)
Un\G118, Un\G150)
CH Heater disconnection alert setting (Un\G58,
Un\G90, Un\G122, Un\G154)
Un\G90, Un\G122, Un\G154)
CH Heating control output cycle setting (Un\G47,
Un\G79, Un\G111, Un\G143)
Un\G79, Un\G111, Un\G143)
CH Heating proportional band (Ph) setting (Un\G35,
Un\G67, Un\G99, Un\G131)
Un\G67, Un\G99, Un\G131)
CH Heating transistor output flag (Un\G21 to Un\G24)