Multi-Tech Systems MTS2SA-T-R ユーザーズマニュアル
Chapter 10
− Modem Mode AT Commands, S-Registers, and Result Codes
Multi-Tech Systems, Inc. MultiConnect Serial-to-Serial Adapter User Guide (S000354A)
122
Register Unit Range Default Description
S27
73 (49Ah) General Bit-Mapped Options Status. Indicates the status of
command options.
Default:
73 (49h) (01001001b)
Bit 2 Leased line control (&Ln)
0 =
Dial up line (&L0) (Default.)
Bits 4 - 5
Internal clock select (&Xn)
0 =
Internal clock (&X0) (Default.)
1 =
External clock (&X1)
2 =
Slave clock (&X2)
Bit 6 CCITT/Bell mode select (Bn)
0 =
CCITT mode (B0)
1 =
Bell mode (B1) (Default.)
Bit 7 - Reserved
S28
0
General Bit-Mapped Options Status.
Indicates bit mapped options
status.
Default: 0
Bits 0 - 1
Default: 0
Bits 0 - 1
Reserved
Bit 2 Reserved (always 0).
Bits 3 - 4
Bits 3 - 4
Pulse dialing (&Pn)
0 = 39%-61% make/break ratio at 10 pulses per second (&P0)
1 = 33%-67% make/break ratio at 10 pulses per second (&P1)
2 = 39%-61% make/break ratio at 20 pulses per second (&P2)
3 = 33%-67% make/break ratio at 20 pulses per second (&P3)
1 = 33%-67% make/break ratio at 10 pulses per second (&P1)
2 = 39%-61% make/break ratio at 20 pulses per second (&P2)
3 = 33%-67% make/break ratio at 20 pulses per second (&P3)
Bit
5-7
Reserved
S29
10 ms
0–255 70 Flash Dial Modifier Timer. Sets the length of time, in units of 10 ms,
that the modem will go on-hook when it encounters the flash (!) dial
modifier in the dial string. S29 is a country dependent parameter. The
S29 value cannot be changed using S29=XX. Default: 70 (700 ms)
for U.S.
modifier in the dial string. S29 is a country dependent parameter. The
S29 value cannot be changed using S29=XX. Default: 70 (700 ms)
for U.S.
S30
10
s 0–255 0
Disconnect Inactivity Timer.
Sets the length of time, in tens of
seconds, that the modem will stay online before disconnecting when
no data is sent or received. In error-correction mode, any data
transmitted or received will reset the timer. In other modes, any data
transmitted will reset the timer. The timer is inoperative in
synchronous mode.
no data is sent or received. In error-correction mode, any data
transmitted or received will reset the timer. In other modes, any data
transmitted will reset the timer. The timer is inoperative in
synchronous mode.
S31
192
(C0h)
General Bit-Mapped Options Status.
Indicates bit mapped options
status.
Default:
192 (C0h) (11000000b)
Bit 0 Single line connect message enable/disable (\Vn)
0 =
Messages controlled by S95, Wn and Vn (\V0) (Default.)
1 =
Single line connect message (\V1)
Bit 1 Reserved (0)
Bits 2-3
Bits 2-3
Error correction progress messages (Wn)
0 =
DTE speed only (W0) (Default.)
1 =
Full reporting (W1)
2 =
DCE (line) speed only (W2)
Bits 4-5
Caller ID (+VCID)
0 =
Caller ID disabled (+VCID=0) (Default.)
1 =
Short (formatted) Caller ID enabled (+VCID=1)
2 =
Long (unformatted) Caller ID enabled (+VCID=2)
Bits 6-7
Reserved (Default = 11b)