RuggedCom RX1000 ユーザーズマニュアル
Chapter 21 - Configuring The DHCP server
Assign a client at switch port 2 address 192.168.1.102.
Assign a client at switch port 3 address 192.168.1.103.
Assign multiple clients at switch port 4 dynamic addresses 192.168.1.151 through
192.168.1.200.
The router serves as the default gateway.
Assign a client at switch port 3 address 192.168.1.103.
Assign multiple clients at switch port 4 dynamic addresses 192.168.1.151 through
192.168.1.200.
The router serves as the default gateway.
1) Enable eth1 in the 'Edit Network Interfaces' menu.
2) Add a new subnet, and configure it for network address 192.168.1.0 with
2) Add a new subnet, and configure it for network address 192.168.1.0 with
netmask 255.255.255.0.
3) Enable the 'Disable NAK of option82 clients for this subnet?' option to
prevent confusing some DHCP clients due to the client being on the same
network as the DHCP server and the DHCP relay agent (the switch).
network as the DHCP server and the DHCP relay agent (the switch).
4) Save it then edit the subnet just created and click 'Edit Client Options'.
5) Set default routers to 192.168.1.1 and save it.
6) Click 'add an address pool' to the subnet.
7) Set the address range to 192.168.1.102 to 192.168.1.102.
8) Click 'Create'.
9) Edit the pool by clicking on the link for the pool with address range
5) Set default routers to 192.168.1.1 and save it.
6) Click 'add an address pool' to the subnet.
7) Set the address range to 192.168.1.102 to 192.168.1.102.
8) Click 'Create'.
9) Edit the pool by clicking on the link for the pool with address range
192.168.1.102 - 192.168.1.102.
10) Click 'add an option82 client'.
11) Give the client a unique alpha numeric name (for example client0102).
12) Set the remote id to the switch MAC address (00:0A:DC:11:22:00 in this
11) Give the client a unique alpha numeric name (for example client0102).
12) Set the remote id to the switch MAC address (00:0A:DC:11:22:00 in this
case).
13) Set the circuit id to the switches circuit id identifier to the port (00:01:00:02
for VLAN 1 port 2 on a RuggedCom switch).
14) Click 'Create'.
15) Click 'Save'.
16) Repeat steps 6) through 15) for clients 192.168.1.103 changing the pool
15) Click 'Save'.
16) Repeat steps 6) through 15) for clients 192.168.1.103 changing the pool
address range and circuit id.
17) Repeat steps 6) through 15) for port 4 using the address range 192.168.1.151
to 192.168.1.200 and the circuit id for port 4.
18) Restart the DHCP server or apply changes.
Multiple Subnets On Separate VLANs Using Option82 On One Switch
In this example the eth1 interface is provided with IP address 192.168.1.1/24
A switch connected to eth1 and using address 192.168.1.2/24
The switch port 1 is connected to the router while its ports 2 through 8 provide DHCP
relay support. The switch has its DHCP relay server address set to router's address
192.168.1.1. The switch has all ports in VLAN 1. The switch base MAC address is
00:0A:DC:11:22:00.
A switch connected to eth1 and using address 192.168.1.2/24
The switch port 1 is connected to the router while its ports 2 through 8 provide DHCP
relay support. The switch has its DHCP relay server address set to router's address
192.168.1.1. The switch has all ports in VLAN 1. The switch base MAC address is
00:0A:DC:11:22:00.
RuggedCom 205