Epson S1D13504 ユーザーズマニュアル
Page 34
Epson Research and Development
Vancouver Design Center
S1D13504
Programming Notes and Examples
X19A-G-002-07
Issue Date: 01/02/01
6.1.2 Simultaneous Display
For Simultaneous Display, only 4/8-bit single passive LCD panels and 9-bit active matrix TFT
panels can be used. Simultaneous Display requires that the panel timing be taken from the CRT
timing registers and thereby limits the number of useful modes supported.
panels can be used. Simultaneous Display requires that the panel timing be taken from the CRT
timing registers and thereby limits the number of useful modes supported.
The configuration of both CRT and panel must not violate the limitations as described in “Frame
Rate Calculation” (Chapter 11) of the S1D13504 Hardware Functional Specification. For example,
on a 640x480 single panel, the maximum values of both the panel pixel clock and CRT frame rate
are 40 MHz and 85 Hz respectively. When pixel depth is less than 8 bpp, the RAMDAC is
programmed with the same values as the Look-Up Table. The S1D13504 does not support Simulta-
neous Display in a color depth greater than 8 bpp.
Rate Calculation” (Chapter 11) of the S1D13504 Hardware Functional Specification. For example,
on a 640x480 single panel, the maximum values of both the panel pixel clock and CRT frame rate
are 40 MHz and 85 Hz respectively. When pixel depth is less than 8 bpp, the RAMDAC is
programmed with the same values as the Look-Up Table. The S1D13504 does not support Simulta-
neous Display in a color depth greater than 8 bpp.
When color depth is 8 bpp, the RAMDAC should be programmed to mimic the recommended values
in the Look-Up Table as described in Section 3.3.2. The recommendation is that the intensities of
the three prime colors (RGB) be distributed evenly. Table 6-3 shows the recommended RAMDAC
palette data for 8 bpp Simultaneous Display. Table 6-4 shows the related register data for some
possible CRT options with an 8-bit Color 640X480 single passive panel.
in the Look-Up Table as described in Section 3.3.2. The recommendation is that the intensities of
the three prime colors (RGB) be distributed evenly. Table 6-3 shows the recommended RAMDAC
palette data for 8 bpp Simultaneous Display. Table 6-4 shows the related register data for some
possible CRT options with an 8-bit Color 640X480 single passive panel.
Table 6-2: Related Register Data for CRT Only
Register
640X480@60Hz
PCLK=25.175MHz
640X480@75Hz
PCLK=31.500MHz
800X600@56Hz
PCLK=36.0 MHz
800X600@60Hz
PCLK=40.0 MHz
Notes
REG[04h]
0100 1111
0100 1111
0110 0011
0110 0011
set horizontal display width
REG[05h]
0001 0011
0001 1000
0001 1011
0001 1111
set horizontal non-display period
REG[06h]
0000 0001
0000 0001
0000 0010
0000 0100
set HSYNC start position
REG[07h]
0000 1011
0000 0111
1000 1000
1000 1111
set HSYNC polarity and pulse width
REG[08h]
1101 1111
1101 1111
0101 0111
0101 0111
set vertical display height bits 7-0
REG[09h]
0000 0001
0000 0001
0000 0010
0000 0010
set vertical display height bits 9-8
REG[0Ah]
0010 1100
0001 0011
0001 1000
0001 1011
set vertical non-display period
REG[0Bh]
0000 1001
0000 0000
0000 0000
0000 0000
set VSYNC start position
REG[0Ch]
0000 0001
0000 0010
1000 0001
1000 0011
set VSYNC polarity and pulse width
REG[0Dh]
0000 1110
0000 1110
0000 1110
0000 1110
set 8 bpp and CRT enable
REG[19h]
0000 0000
0000 0000
0000 0000
0000 0000
set MCLK and PCLK divide
REG[2Ch]
0000 0000
0000 0000
0000 0000
0000 0000
set write mode address to 0
REG[2Eh]
load RAMDAC palette data