Powerware 1500 プリント

The UPS provides both visual and audible status indicators. Visual indicators 
consist of three LEDs to represent the following conditions: 
    On utility power operation
    On battery power operation
    UPS fault/alarm

On Utility (AC mode)

On Battery (Backup mode)

Low Battery

Fault/Output Short

Overload/Check Battery 

 Green Lighting

 Yellow Lighting

 Yellow Flashing

 Red Lighting

 Red Flashing

Backup mode

Battery low

Overload

Replace battery

Fault or output short circuit

Battery over charge

Sounding every 5 seconds

Sounding (two beeps) every 5 seconds

Sounding every 0.5 seconds

Sounding (three beeps) every 30 seconds

Continuous sounding

Sounding (three beeps) every 5 seconds

7AH x 2, 9AH x 2 batteries (1000VA, 1500VA models)

7AH x 1 battery (700VA models)

1

2

3

4

5

6

7

8

9

1

2

3

4

5

6

7

8

9

4

5

6

7

8

9

PW5110 350 USB
PW5110 500 USB
PW5110 700 USB
PW5110 1000 USB
PW5110 1500 USB

Model Numbers

350 VA / 210W
500 VA / 300W
700 VA / 420W
1000 VA / 600W
1500 VA / 900W

Capacity

Transfer time to Battery/AC

Battery Type

6ms typical

Maintenance free lead-acid battery

Battery Specification

Typical Backup Time

LAN / Phone / Fax Protection

Short Circuit Protection

Communication Port

Operation Temperature

Operation Relative Humidity

Storage Temperature

350 VA: 12V 4.5 Ah

500 VA: 12V 5 Ah
750 VA: 12V 7 Ah

1000 VA: (2) 12V 7 Ah
1500 VA: (2) 12V 9 Ah

3 MINUTES MINIMUM AT FULL RATED LOAD

RJ11/RJ45

Circuit Breaker

USB

0 C~40 C

0 to 95% non-condensing

-15 C~50 C

350 VA: 11.9 pounds / 5.4 kg

500 VA: 12.13 pounds / 5.5 kg
700 VA: 15.21 pounds / 6.9 kg 

1000 VA: 28 pounds / 12.7kg

1500 VA: 29.1 pounds / 13.2 kg

350 / 500 / 700 VA: 10.6 x 3.4 x 10 in.

1000 / 1500 VA: 10.6 x 3.4 x 15 in.

Net Weight

Dimensions (HxWxD)

* Due to continuing product improvement programs, specifications are subject to change 
without notice.

Ensure the UPS is securely 
connected to an AC outlet.
Reduce the amount of equipment 
plugged into the “Battery Backup & 
Surge Protection” outlets of the 
UPS.  Reset the circuit breaker by 
pushing it back in. Switch the UPS 
back on.

The UPS is not connected 
to the power source.
Circuit Breaker has 
tripped.

UPS will not turn on

UPS is making a 
continuous sound and the 
“Overload” indicator is on

The “Battery Backup & 
Surge Protection” outlets 
are overload.

Turn off the UPS and reduce the 
amount of equipment connected to 
these outlets.

The UPS battery is 
discharged due to a power 
outage and has not 
recharged.

Charge the battery for 8 hours. The 
UPS runtime is reduced until the 
battery is fully charged.

Unplug non-essential equipment 
(printers, scanners, etc) from the 
Battery Backup outlets and plug 
into 'Surge Only' outlets

UPS does not provide 
expected runtime

Disconnect non-essential equipment 
from the UPS. Reset (push in) the 
circuit breaker and switch the UPS on.
Plug equipment in one-at-a-time. If 
the circuit breaker trips again, 
disconnect the device that caused the 
breaker to trip.
Replace the battery or the battery 
module.
Unplug device from 'Surge Only' outlet 
and move to a 'Battery Backup outlet.

The UPS circuit breaker 

tripped

.

The battery has reached 
the end of its life. 
Equipment plugged into a 
Surge Only outlet.

Red LED Indicator ON

Internal UPS fault.

Contact Technical Support (see 
Service and Support below).

UPS does not power 
essential equipment 
during an outage

For questions and/or problems, please call your local distributor or the 
help desk at one of the following telephone numbers and ask for a UPS technical 
representative.

United States:                                       1.800.356.5737
Europe, Middle East, and Africa:        +44.17.53.608.700
Asia:                                                       +852.2830.3030
Australia:                                               +61.3.9706.5022

Please have the following information ready when you call the Help Desk:
   Model number
   Serial number
   Version number (if available)
   Date of failure or problem
   Symptoms of failure or problem
   Customer return address and contact information
If repair is required, you will be given a Returned Material Authorization 
(RMA) Number. This number must appear on the outside of the package 
and on the Bill of Lading (if applicable). Use the original packaging or 
request packaging from the Help Desk or distributor. Units damaged in shipment 
as a result of improper packaging are not covered under warranty. 
A replacement unit will be shipped, freight prepaid for all units under warranty. 
For additional information please visit us online: 

MA6B411003A(2005/01/25)

120Vac

120Vac

Automatic Voltage Regulation (AVR)

Frequency

Outlets

15%

50 / 60 Hz auto sensing

8 Outlets (4 Battery Backup & Surge Protection; 

4 Surge Protection only)

Lighting / Surge Protection

320 Joules

Nominal Input Voltage

Nominal Output Voltage

4.5AH, 5AH batteries (350VA, 500VA models)

1

2

3

Devices plugged into Back 
up & surge protection 
receptacles exceed the 
rated load for the UPS run 
time