Mitsubishi Electronics XD3200U ユーザーズマニュアル
EN-6
Preparing your projector
1
2
3
Checking accessories
The following accessories are provided with this projector. Check to be sure that all of the accessories are packed in
the package.
the package.
Cables
Remote control parts
Remote control
(290P176-10)
RS-232C cable
(246C598-10)
R6 (size-AA)
battery (two)
RGB cable for PC
(246C597-10)
Others
• Lens cap (attached to the projector)
• Terminal cover (750B017-10)
• Lamp replacement tray (857C132-10)
• CD-ROM (919C165-10)
• Safety Manual/Quick Start up
• Terminal cover (750B017-10)
• Lamp replacement tray (857C132-10)
• CD-ROM (919C165-10)
• Safety Manual/Quick Start up
(871D531-10)
Mini D-SUB
15-pin
Mini D-SUB
15-pin
D-SUB
9-pin
Power supply parts
Power cord (two)
(246C483-10, 246C383-20)
• Used for projector control
by computer.
D-SUB
9-pin
Important:
• The attached power cords are to be used exclusively for this product. Never use them for other products.
• The attached power cords are to be used exclusively for this product. Never use them for other products.
Inserting the batteries into the remote control
1. Remove the rear lid of the remote control.
2. Check the polarity (+), (-) of the batteries, and set them
2. Check the polarity (+), (-) of the batteries, and set them
correctly, inserting their (-) side first.
• If the battery is inserted from the (+) side first, inserting
• If the battery is inserted from the (+) side first, inserting
the (-) side is difficult because the coil spring end hits
on the battery side. If the battery is forced to insert in
this way, the outer label of the battery may get ripped
and it may cause a short-circuit and heating.
on the battery side. If the battery is forced to insert in
this way, the outer label of the battery may get ripped
and it may cause a short-circuit and heating.
3. Attach the rear lid.
Important:
• Use two size-AA batteries (R6).
• Replace the 2 batteries with new ones when the remote
Important:
• Use two size-AA batteries (R6).
• Replace the 2 batteries with new ones when the remote
control is slow to operate.
Removing the batteries from the remote control
Remove the back lid of the remote control and take out the
batteries.
batteries.
Caution:
• Use of a battery of wrong type may cause explosion.
• Only Carbon-Zinc or Alkaline-Manganese Dioxide type batteries should be used.
• Dispose of used batteries according to your local regulations.
• Batteries may explode if misused. Do not recharge, disassemble, or dispose of them in fire.
• Be sure to handle the batteries according to the instructions.
• Load the batteries with its positive (+) and negative (-) sides correctly oriented as indicated on the remote control.
• Keep batteries out of reach of children and pets.
• Remove the batteries, if the remote control is not used for a long time.
• Do not combine a new battery with an old one.
• If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes in
• Use of a battery of wrong type may cause explosion.
• Only Carbon-Zinc or Alkaline-Manganese Dioxide type batteries should be used.
• Dispose of used batteries according to your local regulations.
• Batteries may explode if misused. Do not recharge, disassemble, or dispose of them in fire.
• Be sure to handle the batteries according to the instructions.
• Load the batteries with its positive (+) and negative (-) sides correctly oriented as indicated on the remote control.
• Keep batteries out of reach of children and pets.
• Remove the batteries, if the remote control is not used for a long time.
• Do not combine a new battery with an old one.
• If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes in
contact with your eyes, rinse them with water and then consult your doctor.