Cabletron Systems CSX1000 ユーザーズマニュアル
USER’S GUIDE
408 CyberSWITCH
4.
If the remote resources can not be seen even when the connection is up, then make sure the
AppleTalk address of the remote device is valid. If the remote device is on an unnumbered
network, then AppleTalk an address of 0.0 must be configured for the remote device in the
device table. If it is on a numbered network, the AppleTalk address does not need to be
configured for the device in the device table. However, if it is configured, it must match the
AppleTalk address configured on the remote device.
AppleTalk address of the remote device is valid. If the remote device is on an unnumbered
network, then AppleTalk an address of 0.0 must be configured for the remote device in the
device table. If it is on a numbered network, the AppleTalk address does not need to be
configured for the device in the device table. However, if it is configured, it must match the
AppleTalk address configured on the remote device.
SNMP
Problem:
The SNMP Agent is not functioning.
The SNMP Agent is not functioning.
Action:
1.
1.
Check the configuration of the CyberSWITCH. In order for the SNMP Agent to become
enabled, both the IP option and the SNMP Agent must be enabled in the CyberSWITCH
configuration. (You may check the configuration by using the
enabled, both the IP option and the SNMP Agent must be enabled in the CyberSWITCH
configuration. (You may check the configuration by using the
options
and
snmp
commands
in Manage Mode; however, you can only make changes to these items by using CFGEDIT).
2.
Enter the
dr
command at the administrative console. If the following message appears, the IP
subsystem has initialized successfully:
[IP] IP router is initialized successfully
3.
However, if one of the following messages appears, there is an unexpected condition present
within the CyberSWITCH software. Contact Customer Support.
within the CyberSWITCH software. Contact Customer Support.
[SNMP] SNMP initialization failure - unable to allocate necessary
memory
[SNMP] SNMP initialization failure - unable to open UDP port
Problem:
The CyberSWITCH does not respond to SNMP requests.
The CyberSWITCH does not respond to SNMP requests.
Action:
1.
1.
Enter the command
snmp stats
at the administrative console. If an “
SNMP is not
enabled
” message appears, you must first enable the SNMP Agent (using CFGEDIT).
2.
If the SNMP statistics are displayed, check the value of the “snmpInBadVersions” statistic. If it
is non-zero, the Network Management station is generating request PDUs with an
incompatible SNMP version number. Such requests are discarded by the SNMP agent.
is non-zero, the Network Management station is generating request PDUs with an
incompatible SNMP version number. Such requests are discarded by the SNMP agent.
3.
Check the value of the “snmpInBadCommunityUses” statistic. If it is non-zero, the community
name specified in the request PDUs does not have the proper access rights to perform the
desired request, and the request is discarded. To correct this problem, reconfigure the MIB
access level for the desired community name to the desired access level.
name specified in the request PDUs does not have the proper access rights to perform the
desired request, and the request is discarded. To correct this problem, reconfigure the MIB
access level for the desired community name to the desired access level.
4.
Check the value of the “snmpInASNParseErrs” statistic. If it is non-zero, the network
management station is generating request PDUs that are not properly encoded in ASN.1
format. Such requests are discarded by the SNMP agent.
management station is generating request PDUs that are not properly encoded in ASN.1
format. Such requests are discarded by the SNMP agent.