Motorola T3 Power Broadband ユーザーズマニュアル
Commands and Syntax
Motorola, Inc.
570510-001-00 rev A
Page 9 of 50
C
C
o
o
m
m
m
m
a
a
n
n
d
d
s
s
a
a
n
n
d
d
S
S
y
y
n
n
t
t
a
a
x
x
The Motorola T3 PowerBroadband system can be managed via a Command Line Interface, webUI, and SNMP.
Commands that apply to remote WallPlates, such as Ethernet port configurations and wireless interface, are all
entered on the T3 Switch.
Commands that apply to remote WallPlates, such as Ethernet port configurations and wireless interface, are all
entered on the T3 Switch.
C
C
o
o
m
m
m
m
a
a
n
n
d
d
H
H
i
i
e
e
r
r
a
a
r
r
c
c
h
h
y
y
The Command Line Interface (CLI) implements a hierarchical command structure. Commands are organized as a
high-level command keyword related to a particular function of the device with sub-commands related to sub-
functions.
You may move down in the command hierarchy by entering root keywords and sub-keywords followed by the
enter key. Your current level in the command hierarchy is referred to as the “command context.” The top-level
context is referred to as the “root command context.” You may move up to the previous command context by
using the exit command. The command prompt is the system name, followed by the current command context.
For example, the root command prompt with the default configuration is:
high-level command keyword related to a particular function of the device with sub-commands related to sub-
functions.
You may move down in the command hierarchy by entering root keywords and sub-keywords followed by the
enter key. Your current level in the command hierarchy is referred to as the “command context.” The top-level
context is referred to as the “root command context.” You may move up to the previous command context by
using the exit command. The command prompt is the system name, followed by the current command context.
For example, the root command prompt with the default configuration is:
system>
Full commands may be entered at the root command context. For example:
system> interface dsl enable port1
You may also move down levels in the command hierarchy, which allows you to execute commands with less
repetitive typing.
For example:
system>
interface
system:interface>
dsl
system:interface.dsl> enable port1
system:interface.dsl> enable port3
system:interface.dsl> enable port3
system:interface.dsl>
exit
system:interface>
exit
system>
A
A
d
d
m
m
i
i
n
n
i
i
s
s
t
t
r
r
a
a
t
t
i
i
v
v
e
e
C
C
o
o
m
m
m
m
a
a
n
n
d
d
s
s
Most commands discussed in this guide are administrative commands, which change the configuration of the
system or affect the operation of the system. These commands can only be executed from the admin account.
Configuration changes take affect immediately and are recorded in non-volatile memory (NVRAM) in the default
mode. Alternatively, you may choose not to record changes in NVRAM. In this case, changes will need to be
committed before rebooting the system; otherwise the configuration will revert to the last saved configuration. If
automatic commit is enabled, or the configuration is manually committed, the running configuration will
automatically be restored if the system power cycles or is rebooted.
system or affect the operation of the system. These commands can only be executed from the admin account.
Configuration changes take affect immediately and are recorded in non-volatile memory (NVRAM) in the default
mode. Alternatively, you may choose not to record changes in NVRAM. In this case, changes will need to be
committed before rebooting the system; otherwise the configuration will revert to the last saved configuration. If
automatic commit is enabled, or the configuration is manually committed, the running configuration will
automatically be restored if the system power cycles or is rebooted.
Show Commands
The show commands are used to view configurations, status and/or statistics. These commands can be issued
from either the user or admin account.
from either the user or admin account.