Patton electronic 29XX ユーザーズマニュアル
Dial In User Statistics window
91
Access Server Administrators’ Reference Guide
7 • Dial In
Time Left In Session (diactRemainingSession)
Number of seconds remaining in this session. This value is only displayed if session timeout has been activated.
Number of seconds remaining in this session. This value is only displayed if session timeout has been activated.
Termination Reason (diactTerminateReason)
The reason a call was disconnected.
The reason a call was disconnected.
•
stillActive(0)—Call is currently connected
•
idleTimeout(2)—Call exceeded idle timeout parameter
•
killed(3)—Call terminated by administrator
•
userHangup (5)—DSP discovered remote modem was hung up abruptly. Examples could be that the phone
line was pulled out of the wall jack or the user terminated the communications without closing the connec-
tion down. If the modems are unable to bring up the physical line by successfully negotiating the modula-
tion, userHangup will be registered if the remote modem gave up trying to complete the call.
line was pulled out of the wall jack or the user terminated the communications without closing the connec-
tion down. If the modems are unable to bring up the physical line by successfully negotiating the modula-
tion, userHangup will be registered if the remote modem gave up trying to complete the call.
•
modemCanNotConnect(6)—The modems are not able to bring up the physical line by successfully negotiat-
ing the modulation. The remote access server has given up trying further to complete the physical connection.
ing the modulation. The remote access server has given up trying further to complete the physical connection.
•
pppClose(8)—This termination reason will be given after PPP is initiated and the connection is discon-
nected. An example would be if LCP negotiations failed. Another cause could be if the bundlehead in a
multilink call is terminated before the tunneled call is termination.
nected. An example would be if LCP negotiations failed. Another cause could be if the bundlehead in a
multilink call is terminated before the tunneled call is termination.
•
lcpClose(9)—Close initiated by LCP. normal shutdown of call
•
loginTimeOut(10)—Exceeded login timeout parameter
•
userTerminated(11)—A problem is discovered initiating the dial-in users telnet, rlogin or tcpclear session.
•
maxNumCalls(21)—Exceeds maximum number of channels that can be allocated to the same call.
•
notPapReq(24)—The access server is waiting for a PAP request packet containing the username/password
for a call but the packet received was not a PAP request packet.
for a call but the packet received was not a PAP request packet.
•
noIpPoolAddr(30)—Authentication server did not assign an IP address and access had no IP address pool
defined to assign an IP address
defined to assign an IP address
•
noIpAddr(31)—Authenticator did not return an IP address for the service (e.g. telnet or rlogin) and the
default service defined does not specify the service IP address
default service defined does not specify the service IP address
•
maxLoginAttempts(32)—Exceeded maximum login attempts as defined under the Dial-in link.
•
invalidDefaults(44)—Default service is set to a value other than rlogin, telnet, tcpraw, ppp, slip or vpn
when using a login technique of None. No IP address is defined when using rlogin or telnet. Invalid telnet
or rlogin services ports have been defined in the default service.
when using a login technique of None. No IP address is defined when using rlogin or telnet. Invalid telnet
or rlogin services ports have been defined in the default service.
•
noDspAvailable(45)—When the remote access server attempted to connect the incoming call to an avail-
able DSP, no DSP could be found. Some examples why a DSP could not be found are:
able DSP, no DSP could be found. Some examples why a DSP could not be found are:
–
DSPs are no longer available to the resource pool because they are in reboot or hardware failure states.
–
DSPs are in an unavailable administrative state although they are functional.
–
The DSP resource pool is split between link A and link B and a call has been routed to a link over and
above the number of DSPs allocated to that link.