Radio Shack 20-164 ユーザーズマニュアル
advantages.over.typical.portable.frequency.
counters..
counters..
Signal.Stalker.II.is.more.sensitive.than.
portable.frequency.counters.and.will.detect.
transmissions.at.a.greater.distance..Signal.
Stalker.II.rapidly.searches.the.RF.spectrum.in.
1.MHz.segments..If.it.detects.a.signal,.Signal.
Stalker II searches in finer steps until the signal
source.is.found.
portable.frequency.counters.and.will.detect.
transmissions.at.a.greater.distance..Signal.
Stalker.II.rapidly.searches.the.RF.spectrum.in.
1.MHz.segments..If.it.detects.a.signal,.Signal.
Stalker II searches in finer steps until the signal
source.is.found.
Signal.Stalker.II.can.search.all.frequencies,.
or you can define frequency ranges, to avoid
ranges.with.constant.activity,.such.as.paging.or.
broadcast.transmitters..
or you can define frequency ranges, to avoid
ranges.with.constant.activity,.such.as.paging.or.
broadcast.transmitters..
To use Signal Stalker II:
1.. Hold.the.Signal.Stalker.button.(
1.. Hold.the.Signal.Stalker.button.(
).for.
approximately.1.second..
2.. To.change.the.scanned.band.(All.Band.or.
Police/Fire),.press.FUNC.then.Signal.Stalker.
(
(
)..For.a.list.of.Signal.Stalker.Bands,.see..
Appendix.D.
3.. To.turn.off.a.bank,.press.the.bank.or.group.
number.while.Signal.Stalker.II.is.active.
4.. To.turn.off.Signal.Stalker,.hold.the.Signal.
Stalker.button.(
).again.
Priority mode is not available while using
the Signal Stalker II.
the Signal Stalker II.
Special Signal Stalker
Special.Signal.Stalker.II.divides.the.frequency.
range.by.1.MHz.segments..If.you.lock.out.5.
frequencies.within.1.MHz.segment,.the.scanner.
will.skip.that.segment.in.subsequent.sweeps.
range.by.1.MHz.segments..If.you.lock.out.5.
frequencies.within.1.MHz.segment,.the.scanner.
will.skip.that.segment.in.subsequent.sweeps.
To use Special Signal Stalker II:
1.. Press.FUNC.
2.. Use..or..to.select.“Sp..Stalker”.appears.
1.. Press.FUNC.
2.. Use..or..to.select.“Sp..Stalker”.appears.
for.Special.Signal.Stalker.II.
3.. To.turn.off.Special.Signal.Stalker.II,.press.
FUNC.and.then..or..again.
Locking Out Frequencies
When.you.lock.out.frequencies.during.a.search,.
the.scanner.continues.searching,.but.ignores.
the.locked.out.frequencies..You.can.lock.out.up.
to.50.frequencies.in.each.bank..If.you.try.to.lock.
out.more,.“L/O.Memory.Full!”.appears.
the.scanner.continues.searching,.but.ignores.
the.locked.out.frequencies..You.can.lock.out.up.
to.50.frequencies.in.each.bank..If.you.try.to.lock.
out.more,.“L/O.Memory.Full!”.appears.
While.using.Signal.Stalker.II,.you.can.lock.out.
150.frequencies.if.searching.all.bands.and.
50.frequencies.while.searching.PubSafety.
frequencies..If.you.lock.out.5.frequencies.within.
a.1.MHz.segment,.the.scanner.will.skip.that.
segment.in.subsequent.sweeps.
150.frequencies.if.searching.all.bands.and.
50.frequencies.while.searching.PubSafety.
frequencies..If.you.lock.out.5.frequencies.within.
a.1.MHz.segment,.the.scanner.will.skip.that.
segment.in.subsequent.sweeps.
If you lock out all the frequencies in a
search bank and only that search bank
is activated, “All ranges Locked out!”
appears and the scanner does not search.
search bank and only that search bank
is activated, “All ranges Locked out!”
appears and the scanner does not search.
Signal Stalker II still performs a fine
step search for locked out signals. Signal
Stalker II will not stop on the signal, but
scan may take longer.
step search for locked out signals. Signal
Stalker II will not stop on the signal, but
scan may take longer.
To lock out a frequency:
When.the.scanner.stops.on.a.frequency,.press.
L/OUT..
When.the.scanner.stops.on.a.frequency,.press.
L/OUT..
To review and unlock frequencies:
1.. Press.SRCH.to.enter.search.mode.
1.. Press.SRCH.to.enter.search.mode.