Radio Shack 20-164 ユーザーズマニュアル
6.. If.necessary,.use.the.number.keys.to.enter.a.
new.Offset.frequency.and.press.ENT..The.S.
in.Step.blinks.
in.Step.blinks.
If you try to program an offset frequency
in the UHF-Hi bands (806-960 MHz), the
scanner ignores the entry.
in the UHF-Hi bands (806-960 MHz), the
scanner ignores the entry.
7.. While.the.S.in.Step.blinks,.repeatedly.press.
.or..to.select.the.step.number:.5.0,.
6.25,.10.0,.12.5,.15.0,.18.75,.20.0,.25.0,.30.0,.
31.25,.35.0,.37.5,.40.0,.43.75,.or.50.0.kHz,.
then.press.ENT.
31.25,.35.0,.37.5,.40.0,.43.75,.or.50.0.kHz,.
then.press.ENT.
8
.. Press.PGM.
UHF-Hi (806-960 MHz)
To program 800 MHz Motorola trunking:
1.. Press.PGM.then.TRUNK.to.enter.the.ID.
To program 800 MHz Motorola trunking:
1.. Press.PGM.then.TRUNK.to.enter.the.ID.
program.mode.
2.. Press.FUNC,.then.press..or...The.bank.
number.increases.or.decreases.by.one..If.
you.hold.down..or.,.the.bank.number.
increases.or.decreases.continuously.
you.hold.down..or.,.the.bank.number.
increases.or.decreases.continuously.
3.. If.necessary,.repeatedly.press.MODE.to.
select.“Motorola.”
4.. Press.FUNC.then.3..NORMAL.appears.
5.. Press..or..to.select.NORMAL.or.
5.. Press..or..to.select.NORMAL.or.
SPLINTER.and.press.ENT..If.you.are.
uncertain.about.the.base.frequency,.use.
NORMAL..
uncertain.about.the.base.frequency,.use.
NORMAL..
.
The.base.frequency.in.NORMAL.is.851.0125.
MHz..The.base.frequency.in.SPLINTER.is.
851.0000.MHz....If.you.cannot.receive.with.
the.NORMAL.setting,.change.to.SPLINTER..
MHz..The.base.frequency.in.SPLINTER.is.
851.0000.MHz....If.you.cannot.receive.with.
the.NORMAL.setting,.change.to.SPLINTER..
EDACS Trunking Setup
EDACS.(GE/Ericsson).systems.transmit.Talk.
Group.ID.data.on.a.dedicated.control.channel..
Scanning.requires.clear.reception.of.the.
control.channel.at.all.times,.so.EDACS.systems.
generally.have.a.smaller.usable.area..You.
can.manually.select.the.data.channel,.but.an.
external.antenna.can.greatly.improve.EDACS.
scanning..If.you.are.programming.frequencies.
for.an.EDACS.sysstem,.you.must.store.them.
in.the.Logical.Channel.Number.order.(usually.
listed.as.LCN#).
Scanning.requires.clear.reception.of.the.
control.channel.at.all.times,.so.EDACS.systems.
generally.have.a.smaller.usable.area..You.
can.manually.select.the.data.channel,.but.an.
external.antenna.can.greatly.improve.EDACS.
scanning..If.you.are.programming.frequencies.
for.an.EDACS.sysstem,.you.must.store.them.
in.the.Logical.Channel.Number.order.(usually.
listed.as.LCN#).
LTR Trunking Setup
LTR.systems,.assign.each.frequency.a.Home.
Repeater.(HR).number,.and.are.frequently.
programmed.with.unique.ID.codes.for.each.
radio..LTR.Talk.Group.IDs.are.organized.in.a.
specific order, and to scan, you must program
the.frequencies.in.HR.order..LTR.systems.are.
used.primarily.by.businesses,.such.as.taxicabs,.
delivery.trucks,.and.repair.services.
Repeater.(HR).number,.and.are.frequently.
programmed.with.unique.ID.codes.for.each.
radio..LTR.Talk.Group.IDs.are.organized.in.a.
specific order, and to scan, you must program
the.frequencies.in.HR.order..LTR.systems.are.
used.primarily.by.businesses,.such.as.taxicabs,.
delivery.trucks,.and.repair.services.
LTR.systems.use.a.Home.Repeater.as.part.of.
their.Talk.Group.ID.
their.Talk.Group.ID.
To save a correct Home Repeater:
1.. Save.the.LTR.channels.in.any.order..
2.. Set.the.bank.to.Open.mode..
3.. Manually.select.LT.channels.and.watch.the.
1.. Save.the.LTR.channels.in.any.order..
2.. Set.the.bank.to.Open.mode..
3.. Manually.select.LT.channels.and.watch.the.
LTR.data.on.the.display..
.
Your.scanner.displays.the.LTR.Talk.Group.
ID.and.a.number.preceded.by.“R.”.The.“R”.
number.is.the.Home.Repeater.number.for.
the.transmission..
ID.and.a.number.preceded.by.“R.”.The.“R”.
number.is.the.Home.Repeater.number.for.
the.transmission..
4.. The.assigned.Home.Repeater.channel.must.
equal.the.Home.Repeater.number..For.
example,.R12.must.be.programmed.into.
Channel.12.
example,.R12.must.be.programmed.into.
Channel.12.