Intel 253668-032US ユーザーズマニュアル
Vol. 3 10-11
ADVANCED PROGRAMMABLE INTERRUPT CONTROLLER (APIC)
1. Using the APIC global enable/disable flag in the IA32_APIC_BASE MSR (MSR
address 1BH; see
):
— When IA32_APIC_BASE[11] is 0, the processor is functionally equivalent to
an IA-32 processor without an on-chip APIC. The CPUID feature flag for the
APIC (see
APIC (see
) is also set to 0.
— When IA32_APIC_BASE[11] is set to 0, processor APICs based on the 3-wire
APIC bus cannot be generally re-enabled until a system hardware reset. The
3-wire bus loses track of arbitration that would be necessary for complete re-
enabling. Certain APIC functionality can be enabled (for example:
performance and thermal monitoring interrupt generation).
3-wire bus loses track of arbitration that would be necessary for complete re-
enabling. Certain APIC functionality can be enabled (for example:
performance and thermal monitoring interrupt generation).
— For processors that use Front Side Bus (FSB) delivery of interrupts, software
may disable or enable the APIC by setting and resetting
IA32_APIC_BASE[11]. A hardware reset is not required to re-start APIC
functionality, if software guarantees no interrupt will be sent to the APIC as
IA32_APIC_BASE[11] is cleared.
IA32_APIC_BASE[11]. A hardware reset is not required to re-start APIC
functionality, if software guarantees no interrupt will be sent to the APIC as
IA32_APIC_BASE[11] is cleared.
— When IA32_APIC_BASE[11] is set to 0, prior initialization to the APIC may be
lost and the APIC may return to the state described in
2. Using the APIC software enable/disable flag in the spurious-interrupt vector
register (see Figure 10-31):
— If IA32_APIC_BASE[11] is 1, software can temporarily disable a local APIC at
— If IA32_APIC_BASE[11] is 1, software can temporarily disable a local APIC at
any time by clearing the APIC software enable/disable flag in the spurious-
interrupt vector register (see Figure 10-31). The state of the local APIC when
in this software-disabled state is described in
interrupt vector register (see Figure 10-31). The state of the local APIC when
in this software-disabled state is described in
— When the local APIC is in the software-disabled state, it can be re-enabled at
any time by setting the APIC software enable/disable flag to 1.
For the Pentium processor, the APICEN pin (which is shared with the PICD1 pin) is
used during power-up or RESET to disable the local APIC.
Note that each entry in the LVT has a mask bit that can be used to inhibit interrupts
from being delivered to the processor from selected local interrupt sources (the
LINT0 and LINT1 pins, the APIC timer, the performance-monitoring counters, the
thermal sensor, and/or the internal APIC error detector).
used during power-up or RESET to disable the local APIC.
Note that each entry in the LVT has a mask bit that can be used to inhibit interrupts
from being delivered to the processor from selected local interrupt sources (the
LINT0 and LINT1 pins, the APIC timer, the performance-monitoring counters, the
thermal sensor, and/or the internal APIC error detector).
10.4.4
Local APIC Status and Location
The status and location of the local APIC are contained in the IA32_APIC_BASE MSR
(see
(see
). MSR bit functions are described below:
•
BSP flag, bit 8 ⎯ Indicates if the processor is the bootstrap processor (BSP).
See
Following a power-up or
RESET, this flag is set to 1 for the processor selected as the BSP and set to 0 for
the remaining processors (APs).
the remaining processors (APs).