Panasonic WJ-GXE500E 操作ガイド
23
Reset the settings/Reboot the unit [Default reset]
It is possible to reset the settings or reboot the unit on the [Default reset] tab of the "Maintenance" page on the
setup menu.
The settings and the HTML data of the unit can be initialized and reboot of the camera and the unit can be per-
formed on this page.
setup menu.
The settings and the HTML data of the unit can be initialized and reboot of the camera and the unit can be per-
formed on this page.
[Reset to the default (Except the network settings)]
Click the [Execute] button to reset the settings of the
unit and RS-485 command table to the default. Note
that the network settings will not be reset.
It is impossible to operate the unit for around 2 minutes
after the initialization.
Click the [Execute] button to reset the settings of the
unit and RS-485 command table to the default. Note
that the network settings will not be reset.
It is impossible to operate the unit for around 2 minutes
after the initialization.
Note:
• The following network settings will not be reset.
On/Off for DHCP, IP address, subnet mask, default
On/Off for DHCP, IP address, subnet mask, default
gateway, HTTP port, line speed, bandwidth control
(bit rate), time & date
(bit rate), time & date
[Load the default HTML files (setup menu).]
Click the [Execute] button to reset the settings of the
unit, RS-485 command table and HTML file to the
default. Note that the network settings will not be reset.
It is impossible to operate the unit for around 2 minutes
after the initialization.
Click the [Execute] button to reset the settings of the
unit, RS-485 command table and HTML file to the
default. Note that the network settings will not be reset.
It is impossible to operate the unit for around 2 minutes
after the initialization.
[Reset to the default and load the default HTML
files.]
Click the [Execute] button to reset the settings of the
unit, RS-485 command table and HTML file to the
default. Note that the network settings will not be reset.
It is impossible to operate the unit for around 5 minutes
after the initialization.
files.]
Click the [Execute] button to reset the settings of the
unit, RS-485 command table and HTML file to the
default. Note that the network settings will not be reset.
It is impossible to operate the unit for around 5 minutes
after the initialization.
Note:
• The following network settings will not be reset.
On/Off for DHCP, IP address, subnet mask, default
On/Off for DHCP, IP address, subnet mask, default
gateway, HTTP port, line speed, bandwidth control
(bit rate), time & date
(bit rate), time & date
[Camera restart]
Click the [Execute] button to restart all the cameras
connected to the unit. After restart, it is impossible to
control the camera around 1 minute.
Click the [Execute] button to restart all the cameras
connected to the unit. After restart, it is impossible to
control the camera around 1 minute.
[Unit restart]
Click the [Execute] button to reboot the unit.
The unit will be inoperable for around 2 minutes after
the restart just as when the power is turned on.
Click the [Execute] button to reboot the unit.
The unit will be inoperable for around 2 minutes after
the restart just as when the power is turned on.
Note:
• To initialize the network settings (☞ page 54), turn
off the power of the unit, then turn on the power
again while holding down the [INITIAL SET] button
on the unit for 5 seconds. Wait around 2 minutes
after releasing the button. The unit will start up and
the settings including the network settings will be
initialized.
again while holding down the [INITIAL SET] button
on the unit for 5 seconds. Wait around 2 minutes
after releasing the button. The unit will start up and
the settings including the network settings will be
initialized.
Do not turn off the power of the unit until the initial-
ization is complete and the SDHC/SD memory card
error LED lights up.
error LED lights up.
• The notification function allows users to provide the
notification of the error to the specified mail address
and an original alarm destination when an error such
as no SD memory card insertion after the reboot or
a locked SD memory card insertion occurs. (☞ Page
48)
and an original alarm destination when an error such
as no SD memory card insertion after the reboot or
a locked SD memory card insertion occurs. (☞ Page
48)