Sharp R-1501 ユーザーズマニュアル

26

1. Disconnect the power supply cord, and uncoil the power

supply cord.

2. To discharge the high voltage capacitor, wait for 60

seconds.

3. Remove the turntable tray and support from the oven cavity.
4. If the exhaust damper assembly is installed, remove the

one (1) screw holding the exhaust  damper assembly to
the rear stay, and remove the exhaust  damper assembly
by sliding it backward.

5. Remove the two (2) screws holding the oven (outer case

cabinet) to the top cabinet.

6. While supporting the front of the oven, pull down the two

(2) mounting levers and release the oven from the unit
mounting plate.

7. Pull the power cord out of the wall cabinet and remove

the oven.

8. The oven is now free and can be placed on the work

surface selected for servicing the oven.

9. Installation is the reverse of this procedure.

Remove the oven from the wall, referring to "REMOVAL OF
OVEN FROM WALL" and proceed as follows;
1. Disconnect the power supply cord.
2. Open the door and block it open.
3. To discharge the high voltage capacitor, wait for 60

seconds.

4. Remove four (4) screws holding the rear stay to the hood

fan motor or the oven, and remove it.

5. Remove the six (6) screws from the rear of the outer case

cabinet and one (1) screw at front.

6. Slide the outer case cabinet back about 1 inch (3 cm) to

free it from retaining clips on the cavity face plate.

7. Disconnect the three (3) pin connector of the power

supply cord from the wiring harness and remove the
power supply cord together with the outer case.

8. Nip the cord bushing with bushing pliers and release it

from the outer case cabinet.

9. Remove the cord bushing and the power supply cord

from the outer case cabinet.

10.Now, the power supply cord is free.
CAUTION: 1. DISCONNECT OVEN FROM POWER

SUPPLY BEFORE REMOVING OUTER
CASE.

2. DISCHARGE THE HIGH VOLTAGE

CAPACITOR BEFORE TOUCHING ANY
OVEN COMPONENTS OR WIRING.

1. Disconnect the power supply cord, remove the oven

from wall, and remove outer case. (Refer to procedure of
"REMOVAL OF OVEN FROM WALL" AND  "OUTER
CASE REMOVAL".) And proceed as follows.

2. Open the door and block it open.
3. To discharge the high voltage capacitor, wait for 60

seconds.

4. Remove three (3) screws holding the hood intake duct R

to the oven cavity top plate, the oven cavity front flange
and the fan duct. And remove the hood intake duct R.

5. Disconnect main wire harness from transformer.
6. Disconnect high voltage wire A from the transformer.
7. Disconnect filament leads of transformer from the

magnetron and capacitor.

8. Remove two (2) screws holding the transformer to base

plate R.

Re-install
1. Install by sliding the transformer on the base plate R with

its primary terminals toward the outer case.

2. Secure the transformer with two (2) screws to base plate

R.

3. Re-connect wire leads (primary and high voltage) to the

transformer and filament leads of transformer to
magnetron and high voltage capacitor. Refer to
"PICTORIAL DIAGRAM".

4. Re-install the hood intake duct R to the oven cavity top

plate, the oven cavity front flange and the fan duct with
three (3) screws.

5. Re-install the outer case and check that oven is operating

properly.

CAUTION: MAKE SURE THE WIRE LEADS NEVER

TOUCH THE FAN BLADE.

5. Pull the hood exhaust louver from the oven cavity by

pushing the right and left tabs of the hood exhaust louver
to remove.

6. Now, the hood exhaust louver is free.

1. Disconnect the power supply cord and remove the oven

from wall and remove outer case. (Refer to procedure of
"Removal of Oven from Wall" and "Outer case Removal")

2. Open the door and block it open.
3. To discharge the high voltage capacitor, wait for 60

seconds.

Hood exhaust louver

Left tab

Right tab

Screw

Screw

Screw