Chicago Electric 42933 ユーザーズマニュアル

SKU 42933 

Page 20

Saw will not make a square 

crosscut or a good 60° mitre 

cut.

Arm is not perpendicular to the rip fence

1. 

Too much play between the arm and column

2. 

Yoke too loose when clamped to carriage

3. 

Dust between stock and rip fence

4. 

Table is not parallel with arm

5. 

Rip Fence is not straight. 

6. 

Rear edge of table A not straight

7. 

Adjust the crosscut travel with the rip fence

1. 

Tighten the column sleeve bolt

2. 

Adjust Yoke clamp handle

3. 

Clean worktable

4. 

Adjust Table A

5. 

Replace rip fence.

6. 

Sand or replace Table A

7. 

60° cut not accurate

Saw Blade not perpendicular to worktable

1. 

Too much play between arm and column

2. 

Yoke is too loose when clamped to carriage

3. 

Bevel Lock Knob is loose

4. 

Table is not parallel with arm

5. 

Adjust Saw Blade

1. 

Tighten column sleeve bolt

2. 

Adjust Yoke Clamp Handle

3. 

Adjust Bevel Lock Knob

4. 

Adjust Table A

5. 

Workpiece has a tendency 

to walk away from the fence 

when ripping

Saw Blade is not parallel with the fence. 

1. 

Arm is not perpendicular to the rip fence.

2. 

Adjust Saw Blade

1. 

Adjust cross cut travel with rip fence

2. 

Saw Blade tends to advance 

over the stock too fast

Dull Saw Blade

1. 

Not pulling the Saw Blade properly

2. 

Replace or sharpen blade

1. 

Draw Saw Blade across stock with a slow 

2. 

and steady pull

Cut depth varies from one end 

to the other

Too much play between the arm and column

Tighten column sleeve bolt

Saw does not travel smoothly 

in arm tracks

Dirty tracts

1. 

Bad Bearings

2. 

Clean tracts

1. 

Replace Bearings

2. 

Elevating Handle slips when 

elevating or lowering the Saw 

Blade

Screw loose on Elevating Handle

Tighten Screw

Clamping knobs do not hold 

motor assembly to the set 

position(s)

Treads stripped on knob(s)

Replace knob(s)

Saw Blade scores workpiece, 

not giving a good finished cut

Saw Blade is leaning to one side

1. 

Too much play between arm and column

2. 

Yoke too loose when clamped to carriage

3. 

Saw Blade bent or dull

4. 

Not feeding saw properly 

5. 

Using improper Saw Blade for finish cut 

6. 

desired

Adjust Saw Blade square to rip fence

1. 

Tighten column sleeve bolt

2. 

Adjust Yoke Clamp Handle

3. 

Replace Saw Blade

4. 

Draw the Saw Blade across stock with a 

5. 

slow and steady pull
Replace Saw Blade

6. 

Saw Blade or dado blades 

tend to push stock to one side 

when cross-cutting

Saw Blade is heeling

1. 

Too much play between arm and column

2. 

Yoke too loose when clamped to carriage

3. 

Rip fence not straight

4. 

Dull Saw Blade

5. 

Adjust Saw Blade square to the rip fence

1. 

Tighten column sleeve bolt

2. 

Adjust Yoke Clamp Handle

3. 

Replace rip fence

4. 

Replace or sharpen Saw Blade

5. 

Saw Blade Stalls when ripping

Arbor Nut loose

1. 

Dull Saw Blade

2. 

Saw Blade not parallel to fence

3. 

Tighten

1. 

Replace or sharpen

2. 

Adjust Saw Blade or fence to parallel

3. 

Motor will not reach full speed 

or power

Faulty ON/OFF Switch 

1. 

Circuit overloaded with other appliances

2. 

Motor windings burned out

3. 

Circuit used is under rated for this 

4. 

application

Have the Switch unit checked by a qualified 

1. 

technician
Use a different circuit for the machine

2. 

Replace motor

3. 

Use a different circuit with sufficient power 

4. 

for this machine

Motor overheats, stalls, trips 

the circuit breakers or fuses

Overloaded motor

1. 

Improper cooling caused by excessive 

2. 

sawdust accumulation around the motor
Motor winding burned out or open

3. 

Power source circuit breakers do not have 

4. 

sufficient power capacity

Feed stock into Saw Blade more slowly

1. 

Clean motor housing with compressed air 

2. 

Replace motor using a qualified technician

3. 

Install proper size circuit breakers or change 

4. 

circuits to one with more capacity