DeWALT DW717 ユーザーズマニュアル
English
7
English
7
5. Return the guard bracket to its original position and firmly tighten the guard bracket
screw to hold bracket in place.
WARNING:
• The guard bracket must be returned to its original position
• The guard bracket must be returned to its original position
and the screw tightened before activating the saw.
• Failure to do so may allow the guard to contact the
spinning saw blade resulting in damage to the saw and
severe personal injury.
severe personal injury.
Transporting the Saw
WARNING: To reduce the risk of serious personal injury, turn off the tool and disconnect
it from the power source before attempting to move it, change accessories or make any
adjustments accept as written in laser adjustment instructions.
adjustments accept as written in laser adjustment instructions.
WARNING: To reduce the risk of serious personal injury, ALWAYS lock the rail lock
knob, miter lock handle, bevel lock handle, lock down pin and fence adjustment knobs
before transporting saw.
In order to conveniently carry the miter saw from place to place, a carrying handle has
been included on the top of the saw arm and hand indentations in the base, as shown in
Figure 4.
before transporting saw.
In order to conveniently carry the miter saw from place to place, a carrying handle has
been included on the top of the saw arm and hand indentations in the base, as shown in
Figure 4.
Adjustments
WARNING: To reduce the risk of serious personal injury, turn off the tool and disconnect
it from the power source before attempting to move it, change accessories or make any
adjustments accept as written in laser adjustment instructions.
NOTE: Your miter saw is fully ande ad accurately adjusted at the factory at the time
of manufacture. If readjustment due to shipping and handling or any other reason is
required, follow the steps below to adjust your saw.
Once made, these adjustments should remain accurate. Take a little time now to follow
these directions carefully to maintain the accuracy of which your saw is capable.
adjustments accept as written in laser adjustment instructions.
NOTE: Your miter saw is fully ande ad accurately adjusted at the factory at the time
of manufacture. If readjustment due to shipping and handling or any other reason is
required, follow the steps below to adjust your saw.
Once made, these adjustments should remain accurate. Take a little time now to follow
these directions carefully to maintain the accuracy of which your saw is capable.
MITER SCALE ADJUSTMENT (FIG. 5)
Place a square against the saw’s fence and blade, as shown. (Do not touch the tips
of the blade teeth with the square. To do so will cause an inaccurate measure ment.)
Loosen the miter lock handle and swing the miter arm until the miter latch locks it at
the 0 miter position. Do not tighten the lock handle. If the saw blade is not exactly
perpendicular to the fence, loosen the four screws that hold the miter scale to the base
and move the scale left or right until the blade is perpendicular to the fence, as measured
with the square. Retighten the four screws. Pay no attention to the reading of the miter
pointer at this time.
Place a square against the saw’s fence and blade, as shown. (Do not touch the tips
of the blade teeth with the square. To do so will cause an inaccurate measure ment.)
Loosen the miter lock handle and swing the miter arm until the miter latch locks it at
the 0 miter position. Do not tighten the lock handle. If the saw blade is not exactly
perpendicular to the fence, loosen the four screws that hold the miter scale to the base
and move the scale left or right until the blade is perpendicular to the fence, as measured
with the square. Retighten the four screws. Pay no attention to the reading of the miter
pointer at this time.
BEVEL LOCK
HANDLE
RAIL LOCK
KNOB
RAIL SET
SCREW
ADJUSTMENT
MOTOR
HOUSING
KERF
PLATE
MITER LATCH
BUTTON
MITER LOCK
HANDLE
BENCH MOUNTING HOLES
FENCE
ADJUSTMENT
KNOB
(ONE EACH SIDE)
BLADE
WRENCH
LOCK DOWN
PIN
BEVEL
SCALE
SCALE
BEVEL LATCH
LEVER
(one each side)
MOTOR
ENDCAP
MITER LATCH
OVERRIDE
LIFTING
HANDLE
BELT COVER
RAILS
GROOVING
STOP
BEVEL
LATCH
LATCH
PLATES
DUST SPOUT
FENCE
HAND
INDENTATION
TABLE
MITER
SCALE
BLADE
GUARD
TRIGGER
SWITCH
THUMBSCREW
FIG. 4
SLIDE
STOP