DeWALT DWE6000 ユーザーズマニュアル

Deﬁ nitions: Safety Guidelines

The definitions below describe the level of severity for each signal word. Please read the
manual and pay attention to these symbols.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result

in minor or moderate injury.
NOTICE: Indicates a practice not related to personal injury which, if not avoided, may
result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D

WALT TOOL, CALL

US TOLL FREE AT: 1-800-4-D

WALT (1-800-433-9258).

WARNING: To reduce the risk of injury, read the instruction manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence

of flammable liquids, gases or dust. Power tools create sparks which may ignite the
dust or fumes.

c) Keep children and bystanders away while operating a power tool. Distractions can

cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do

not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,

ranges and refrigerators. There is an increased risk of electric shock if your body is
earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power tool

will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging

the power tool. Keep cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for

outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable, use a ground fault

circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric
shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use a power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention while operating power tools
may result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection. Protective

equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off position before

connecting to power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energizing power tools that have
the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A wrench

or a key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables better

control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing

and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught
in moving parts.

g) If devices are provided for the connection of dust extraction and collection

facilities, ensure these are connected and properly used. Use of dust collection can
reduce dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power tool for your application. The

correct power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off. Any power tool

that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the

power tool before making any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce the risk of starting the power tool
accidentally.

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired before use. Many accidents
are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits, etc. in accordance with these

instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended could
result in a hazardous situation.

INSTRUCTION MANUAL

GUIDE D’UTILISA

TION

MANUAL DE INSTRUCCIONES

DWE6000

Laminate T

rimmer

Détour

euse à stratifiés

Desbastador laminar

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SER

VICIO

Y PÓLIZA DE GARANTÍA.

ADVER

TENCIA:

LÉASE ESTE

INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286

WALT

The following are trademarks for one or more D

WALT power tools: the yellow and black color scheme, the “D” shaped

air intake grill, the array of pyramids on the handgrip, the kit box configuration, and the array of lozenge-shaped humps on
the surface of the tool.

5) SERVICE

a) Have your power tool serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

Additional Safety Rules for Laminate Trimmer

• Hold power tool by insulated gripping surfaces, because the cutter may contact its

own cord. Cutting a “live” wire may make exposed metal parts of the power tool “live” and
shock the operator.

• Use clamps or another practical way to secure and support the workpiece to a

stable platform. Holding the work by hand or against your body leaves it unstable and may
lead to loss of control.

• Always follow the bit manufacturer’s speed recommendations as some bit designs

require specific speeds for safety or performance. If you are unsure of the proper speed
or are experiencing any type of problem, contact the bit manufacturer.

• DO NOT CUT METAL.
• Keep handles and gripping surfaces dry, clean, and free from oil and grease. This

will enable better control of the tool.

• Maintain firm grip with both hands on laminate trimmer to resist starting torque.
• Keep hands away from cutting area. Never reach under the workpiece for any

reason. Keep the laminate trimmer base firmly in contact with the workpiece when cutting.
These precautions will reduce the risk of personal injury.

• Never run the motor unit when it is not inserted into the base. The motor is not

designed to be handheld.

•  Keep cutting pressure constant. Do not overload motor.
•  Check to see that the cord will not snag or impede the trimming operation.
•  Use sharp bits. Dull bits may cause the laminate trimmer to swerve or stall under pressure.
•  Be sure that the bit is clear of the workpiece before starting the motor. If the bit is in

contact with the workpiece when the motor starts, it could make the laminate trimmer jump,
causing damage or injury.

• ALWAYS disconnect tool from power source before making adjustments or

changing bits.

•  Keep hands clear of bit when motor is running to prevent personal injury.
•  NEVER touch the bit immediately after use. It may be extremely hot.
•  Provide clearance under workpiece for bit when through-cutting.
•  Tighten collet nut securely with provided wrench (17 mm) to prevent the bit from

slipping.

•  Never tighten collet nut without a bit.
•  Not recommended for use in a router table.
•  Avoid climb-cutting (cutting in direction opposite than shown in Figure 8). Climb-

cutting increases the chance for loss of control resulting in possible injury. When
climb-cutting is required (backing around a corner), exercise extreme caution to maintain
control of trimmer. Make smaller cuts and remove minimal material with each pass.

• Be sure that the motor has stopped completely before you lay the laminate trimmer

down. If the bit head is still spinning when the tool is laid down, it could cause injury or
damage.

• Do not press spindle lock button while the motor is running. Doing so can damage

the spindle lock.

• Do not use AC only rated tools with a DC power supply. While the tool may appear to

work, the electrical components of the AC rated tool are likely to fail and create a hazard to
the operator.

• If cutting into existing walls or other blind areas where electrical wires may exist is

unavoidable, disconnect all fuses or circuit breakers feeding this worksite.

• Always make sure the work surface is free from nails and other foreign objects.

Cutting into a nail can cause the bit and the tool to jump and damage the bit.

• Never lay workpiece on top of hard surfaces like concrete, stone etc... Protruding

cutting bit may cause tool to jump.

• Do not leave tool running. Operate tool only when hand-held.
• Air vents often cover moving parts and should be avoided. Loose clothes, jewelry or

long hair can be caught in moving parts.

• An extension cord must have adequate wire size (AWG or American Wire Gauge)

for safety. The smaller the gauge number of the wire, the greater the capacity of the cable,
that is 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in
line voltage resulting in loss of power and overheating. When using more than one extension
to make up the total length, be sure each individual extension contains at least the minimum
wire size. The following table shows the correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge
number, the heavier the cord.

Minimum Gauge for Cord Sets

Ampere Rating

Volts

Total Length of Cord in Feet (meters)

120 V

25 (7.6)

50 (15.2)

100 (30.5)

150 (45.7)

240 V

50 (15.2)

100 (30.5)

200 (61.0)

300 (91.4)

More

Than

Not More

Than

AWG

Not Recommended

WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses.

Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY
EQUIPMENT:

•  ANSI Z87.1 eye protection (CAN/CSA Z94.3),
•  ANSI S12.6 (S3.19) hearing protection,
•  NIOSH/OSHA/MSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to the State of California to cause cancer, birth
defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,
•

crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with approved
safety equipment, such as those dust masks that are specially designed to filter out microscopic
particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,

and other construction activities. Wear protective clothing and wash exposed areas
with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust, which may cause serious and

permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure. Direct particles away from face and body.

WARNING: Always wear proper personal hearing protection that conforms to ANSI

S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product
may contribute to hearing loss.
• The label on your tool may include the following symbols. The symbols and their definitions

are as follows:

V .....................volts

A .........................amperes

Hz ...................hertz

W ........................watts

min .................minutes

or AC .............alternating current

or DC .....direct current

or AC/DC......alternating or direct current

...................Class I Construction

no .......................no load speed

.......................(grounded) n

.........................rated

speed

...................Class II Construction

.......................earthing terminal

(double insulated)

........................safety alert symbol

…/min ............per minute

BPM ...................beats per minute

IPM .................impacts per minute

RPM ...................revolutions per minute

SPM ...............strokes per minute

sfpm ...................surface feet per minute

SAVE THESE INSTRUCTIONS FOR FUTURE USE

Motor

Be sure your power supply agrees with the nameplate marking. Voltage decrease of more than
10% will cause loss of power and overheating. D

WALT tools are factory tested; if this tool does

not operate, check power supply.

COMPONENTS (Fig. 1)

WARNING: Never modify the power tool or any part of it. Damage or personal injury could

result.
  A. Quick release tabs
  B. Depth adjustment ring
C. On/off switch
  D. Spindle lock button
E. LED light
F. Spindle
G. Micro adjustment scale
H. Locking lever
I.

Base

J. Subbase

K. Sub-base screws
L. Guide pins
M. Locking lever adjustment screw
N. Collet
O. Collet nut
P. Motor unit
Q. Roller bearing/edge guide slot
R. Edge guide
S. Edge guide screw

INTENDED USE
This laminate trimmer is designed for professional flush and bevel trimming of laminated plastics
and other similar materials that have a bonding agent too hard to be trimmed with ordinary tools.
DO NOT use under wet conditions or in presence of flammable liquids or gases.
This laminate trimmer is a professional power tool. DO NOT let children come into contact with
the tool. Supervision is required when inexperienced operators use this tool.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter

Si tiene dudas o comentarios, contáctenos.

1-800-4-D

• www

.dewalt.com