Cub Cadet 394 ユーザーズマニュアル
12
SECTION III. ADJUSTMENTS
DECK LEVELING ADJUSTMENTS
In order to achieve even cutting, the mower deck must
be properly leveled. This leveling procedure will result in
the left and right blades having corresponding cutting-
edge-to ground measurements within 1/16 inch of each
other. Also, the blades will each have a 1/8 to 1/4 inch
downward tilt toward the front of the tractor. To level the
mower deck, proceed as follows:
In order to achieve even cutting, the mower deck must
be properly leveled. This leveling procedure will result in
the left and right blades having corresponding cutting-
edge-to ground measurements within 1/16 inch of each
other. Also, the blades will each have a 1/8 to 1/4 inch
downward tilt toward the front of the tractor. To level the
mower deck, proceed as follows:
WARNING
Before making any adjustments, place the PTO
switch in the “OFF” position, engage the parking
brake lever, and turn the ignition key to the “OFF”
position. When adjusting the mower deck, be
careful not to cut yourself on the sharp blades.
switch in the “OFF” position, engage the parking
brake lever, and turn the ignition key to the “OFF”
position. When adjusting the mower deck, be
careful not to cut yourself on the sharp blades.
SIDE TO SIDE LEVELING ADJUSTMENT
NOTE: Check for proper tire inflation before checking
and/or making a leveling adjustment.
and/or making a leveling adjustment.
1.
Position the tractor on a hard, level surface, and
use the tractor hydraulic lift system to raise the
deck to its highest position. Stop engine.
use the tractor hydraulic lift system to raise the
deck to its highest position. Stop engine.
2.
Carefully rotate the outer cutting blades so that
they are positioned perpendicular to the tractor
frame (See Figure 16).
they are positioned perpendicular to the tractor
frame (See Figure 16).
Figure 16
3.
Measure and record the distance from the sur-
face to the outer-most cutting edge of the right
blade (See Figure 17). Repeat this step for the left
blade. If the two blade heights are not within 1/16
inch, the deck must be leveled. Note whether the
left blade had the larger or smaller distance be-
tween the cutting edge and level surface. If the
two blade heights are within 1/16 inch, proceed to
FRONT TO BACK LEVELING.
face to the outer-most cutting edge of the right
blade (See Figure 17). Repeat this step for the left
blade. If the two blade heights are not within 1/16
inch, the deck must be leveled. Note whether the
left blade had the larger or smaller distance be-
tween the cutting edge and level surface. If the
two blade heights are within 1/16 inch, proceed to
FRONT TO BACK LEVELING.
Figure 17
4.
Side to side leveling is attained by adjusting the
hex lock nut on the bottom of the LH lift rod,
located below the LH lift link (See Figure 18).
hex lock nut on the bottom of the LH lift rod,
located below the LH lift link (See Figure 18).
Figure 18
5.
Turn the hex lock nut upward (tighten) on the
threads of the lift rod to raise the left side of the
mower deck. Turn the lock nut down (loosen) on
the lift rod threads to lower the left side of the
mower deck.
threads of the lift rod to raise the left side of the
mower deck. Turn the lock nut down (loosen) on
the lift rod threads to lower the left side of the
mower deck.
6.
Recheck the measurements described in step 3.
If the blade measurements are not within 1/16
inch, repeat steps 3 and 5 until the correct mea-
surement is obtained.
If the blade measurements are not within 1/16
inch, repeat steps 3 and 5 until the correct mea-
surement is obtained.
FRONT TO BACK LEVELING
The front lift rod must be correctly adjusted to maintain
the proper pitch of the deck when mowing uneven ter-
rain.
the proper pitch of the deck when mowing uneven ter-
rain.
1.
Position the mower blades so the ends of each
blade point to the front and the rear of the tractor
(Refer to Figure 19).
blade point to the front and the rear of the tractor
(Refer to Figure 19).
OUTER BLADES
PERPENDICULAR TO FRAME
2
3
1
4
1.
Finger guard
2. Blade
3. Hard Level Surface
4. Measure This Distance
3. Hard Level Surface
4. Measure This Distance
LH LIFT ROD
LH LIFT LINK
HEX LOCK NUT