DeLonghi ECAM26455M 取り扱いマニュアル
21
trouBleshootinG
Below is a list of some of the possible malfunctions.
If the problem cannot be resolved as described, contact De’Longhi Customer Experience.
If the problem cannot be resolved as described, contact De’Longhi Customer Experience.
proBlem
possiBle cause
remeDy
The coffee is not hot
The cups were not preheated.
•
Enable the cup warmer, leave the cups at least 20
minutes to warm up.
•
Warm the cups by rinsing them with hot water (N.B.
you can use the hot water function).
The infuser has cooled down because 2/3 minutes
have elapsed since the last coffee was made.
have elapsed since the last coffee was made.
Before making the coffee, warm the infuser by using the
Rinsing function to perform a rinse cycle (page 10).
Rinsing function to perform a rinse cycle (page 10).
Low coffee temperature is set.
In the menu, set a higher coffee temperature.
The coffee is thin or not creamy
enough.
enough.
The coffee is ground too coarsely.
Turn the grinding adjustment dial one click anticlockwise
towards “1” while the coffee mill is in operation (fig.
28). Continue one click at a time until coffee delivery is
satisfactory. The effect is only visible after delivering 2 coffees
(see the section: “adjusting the coffee mill” on page 12).
towards “1” while the coffee mill is in operation (fig.
28). Continue one click at a time until coffee delivery is
satisfactory. The effect is only visible after delivering 2 coffees
(see the section: “adjusting the coffee mill” on page 12).
The coffee is unsuitable.
Use pre-ground coffee for espresso coffee makers
The coffee is delivered too slowly or a
drop at a time.
drop at a time.
The coffee is ground too finely.
Turn the grinding adjustment dial one click clockwise to-
wards “7” while the coffee mill is in operation (fig. 28).
Continue one click at a time until coffee delivery is satisfac-
tory. The effect is only visible after delivering two coffees.
(see the section “adjusting the coffee mill” on page 12).
wards “7” while the coffee mill is in operation (fig. 28).
Continue one click at a time until coffee delivery is satisfac-
tory. The effect is only visible after delivering two coffees.
(see the section “adjusting the coffee mill” on page 12).
Coffee does not come out of one of
the spouts.
the spouts.
The spouts are blocked.
Clean the spouts with a toothpick (fig. 29B).
The milk does not
come out of the milk
spout.
come out of the milk
spout.
the milk container lid is dirty.
Clean the milk container lid as described in the section “clea-
ning the milk container”.
ning the milk container”.
The milk contains
large bubbles and
squirts out of the
milk spout or there
is little froth .
large bubbles and
squirts out of the
milk spout or there
is little froth .
the milk is not cold enough or is not semi-skim-
med.
med.
Use skimmed or semi-skimmed milk at refrigerator tempe-
rature (about 5° c).
If the result is not as you wished, try changing brand of
milk.
rature (about 5° c).
If the result is not as you wished, try changing brand of
milk.
The froth adjustment dial is incorrectly adjusted.
Adjust following the instructions in the section “making
drinks with milk”.
drinks with milk”.
The milk container lid or froth adjustment dial is
dirty
dirty
Clean the milk container lid and dial as described in the sec-
tion “cleaning the milk container”.
tion “cleaning the milk container”.
The hot water/steam nozzle is dirty
Clean the nozzle as described in the section “cleaning the hot
water/steam nozzle”.
water/steam nozzle”.
The milk contains
large bubbles there
is little froth .
large bubbles there
is little froth .
The spout is dirty.
Clean as described in the section “Cleaning the spout after
use”.
use”.
The appliance does not come on.
The connector is not inserted correctly.
Insert the connector as far as it will go in the socket at the
back of the appliance.
back of the appliance.
It is not plugged into the mains socket.
Plug into the mains socket.
The main switch (A7) is not turned on.
Place the main switch in the i position (fig. 2).
The infuser cannot be extracted
The appliance has not been turned off correctly
Turn the appliance off by pressing the
button (page 10)
and wait until the display is completely shut off. At this point
the infuser is in the correct position and can be extracted.
the infuser is in the correct position and can be extracted.