Graco 3A0237L ユーザーズマニュアル
Maintenance
26
3A0237L
Bundle Individual Whip Hoses
Individual whip hoses must be bundled with scuff guards
and air and signal cables. Follow the instructions below
to bundle single and dual heat zone whip hose bundles.
and air and signal cables. Follow the instructions below
to bundle single and dual heat zone whip hose bundles.
See F
IG
. 21 on page 27.
1.
Lay out the A and B material hoses with the male fit-
tings at the same end of the bundle.
tings at the same end of the bundle.
2.
Lay out the air hose (3) with the male fitting at the
same end as the male fittings of the material hoses.
same end as the male fittings of the material hoses.
NOTE: The female fitting of the air hose should be 6
in. (152.4 mm) beyond the female fitting of the mate-
rial hoses.
in. (152.4 mm) beyond the female fitting of the mate-
rial hoses.
3.
Lay out the signal cable (4) with the female end of
the signal cable at the same end as the male ends
of the material hoses.
the signal cable at the same end as the male ends
of the material hoses.
NOTE:
•
The male sign cable connector (4) should be 6
in. beyond the female ends of the material
hoses.
in. beyond the female ends of the material
hoses.
•
Use electrical tape (8) to secure position of sig-
nal cable 10 in. (254 mm) back from the end of
the material hose.
nal cable 10 in. (254 mm) back from the end of
the material hose.
4.
Connect Electrical Connectors.
For Single Zone Heated Whip Hose Bundles:
a.
Place one 6 AWG electrical connector (5) 24 in.
(609.6 mm) from the male material hose fittings.
b.
Connect the 6 AWG wire from each material
hose to the electrical connector (5).
c.
Use black electrical tape (8) to secure the con-
nector to the hose bundle.
For Dual Zone Heated Whip Hose Bundles:
a.
Place two 6 AWG electrical connectors (5) 24
in. (609.6 mm) from the male material hose fit-
tings.
b.
Unlace the 6 AWG wire from each material
hose, trim back the wire, and connect to the
electrical connector (5).
c.
Use black electrical tape (8) to secure both con-
nectors (5) to the correct material hose.
5.
Apply scuff guard (10) on each individual material
hose up to the electrical connector (5).
hose up to the electrical connector (5).
6.
Use red electrical tape (12) to secure the scuff
guard (10) on the red material hose.
guard (10) on the red material hose.
7.
Use blue electrical tape (13) to secure the scuff
guard (10) on the blue material hose.
guard (10) on the blue material hose.
8.
Use electrical tape and temporarily tape the hose
and cable ends together.
and cable ends together.
9.
Feed the scuff guard (4) over the male material
hose fittings.
hose fittings.
10. Use black electrical tape (8) and secure at least 3 in.
(76.2 mm) of scuff guard (4) next to the electrical
connector (5) on side with male material hose fit-
tings.
connector (5) on side with male material hose fit-
tings.
NOTE: Ensure no foam insulation is exposed on
either material hose.
either material hose.
11. Fold the scuff guard (4) over itself and feed the
remaining scuff guard over the entire length of the
bundle.
bundle.
12. Leave excess scuff guard (4) loose on the end with
the female material fittings.
13. Remove electrical tape securing the hose and cable
ends together.
14. Apply warning label (10) in the center of the bundle.
Secure edges with black electrical tape.