JVC TH-C60 ユーザーズマニュアル

7 Handling Discs

• Remove the disc from its case by holding it at 

the edge while pressing the center hole lightly.

• Do not touch the shiny surface of the disc or 

bend the disc.

• Put the disc back in its case after use to 

prevent warping.

• Be careful not to scratch the surface of the disc 

when placing it back in its case. 

• Avoid exposure to direct sunlight, extreme 

temperature and moisture.

To clean the disc 
Wipe the disc with a soft cloth in a straight line 
from center to edge.
• DO NOT use any solvent — such as 

7 Cleaning the system

• Stains on the system should be wiped off with a soft cloth. If the 

system is heavily stained, wipe it with a cloth soaked in water-
diluted neutral detergent and wrung well, then wipe clean with a 
dry cloth.

• Since the system may deteriorate in quality, become damaged or 

get its paint peeled off, be careful about the following.
– DO NOT wipe it with a hard cloth.
– DO NOT wipe it forcefully.
– DO NOT wipe it with thinner or benzine.
– DO NOT apply any volatile substance such as insecticides to it.
– DO NOT allow any rubber or plastic to remain in contact with 

it for a long time.

Power does not come on. The power cord and/or system cord is not connected.

Connect the power cord and system cord correctly. (See 
page 13.)

The remote control does 
not work.

The batteries are exhausted.

Replace the batteries. (See page 7.)

Sunlight is shining directly on the remote sensor.

Hide the remote sensor from direct sunlight.

No sound.

The system cord and/or speaker cord is not connected.

Check the connection. 

The audio cord is not connected to AUX IN (VCR) and/
or DIGITAL IN (DBS) correctly.

Connect the cord correctly. (See page 13.)

An incorrect source has been selected.

Select the correct source. (See page 17.)

No picture is displayed 
on the TV screen.

The video cord is not connected correctly.

Connect the cord correctly. (See page 12.)

The disc or file is not playable.

Use a playable disc or file. (See pages 3 and 4.)

No picture is displayed 
on the TV screen, the 
picture is blurred, or the 
picture is divided into 
two parts.

The scan mode is set to “480p” though the center unit is 
connected to the TV which does not support the 
progressive video input such as a conventional TV.

Change the scan mode to “480i”. (See page 18.)

Video and audio are 
distorted.

The disc is scratched or dirty.

Replace or clean the disc.

A VCR is connected between the center unit and the 
TV.

Connect the center unit and TV directly. (See page 12.)

The picture does not fit 
the TV screen.

The monitor type is not set correctly.

Set “MONITOR TYPE” properly. (See page 34.)

No picture is displayed 
on the TV or no sound 
come out through 
HDMI connection.

A video or audio format not compatible with this 
system and/or TV is played.

Check the video or audio format of the signal to see if it 
is compatible with this system and/or TV.

A HDCP-compatible TV is not connected.

Connect a HDCP-compatible TV. (See page 12.)

The system failed to recognize the TV connected with 
the HDMI cable.

Disconnect the HDMI cable and connect it again.

A HDMI cable longer than 5 m (15 ft) is used.

Use a HDMI cable shorter than 5 m (15 ft) to assure 
stable operation and picture quality.

The broadcast is hard to 
hear because of noise.

Antennas are disconnected.

Reconnect the antennas correctly and securely. (See 
page 8.)

TH-C60-40[J]7.book  Page 39  Monday, February 27, 2006  11:25 AM