Radio Shack 63-1090 プリント
setting your alarm
This product is equipped with a 2-minute
crescendo alarm.
crescendo alarm.
1. Press ((•)) to switch to the alarm display.
2. Press and hold ((•)) again for 2 seconds. The
alarm hour digits blink.
3. Press UP or DOWN to change settings. Press
((•)) to confi rm.
activating your alarm
Press
to activate or deactivate the alarm.
shows in the clock and alarm area when the alarm
is activated.
is activated.
silencing your alarm
When the alarm sounds, it will continue for 2
minutes. Press SNOOZE to silence it for 8 minutes.
Or, press
minutes. Press SNOOZE to silence it for 8 minutes.
Or, press
to turn it off until the next day.
If no button is pressed, the alarm will
automatically silence after 2 minutes. It will then
automatically silence after 2 minutes. It will then
sound again after 8 minutes.
on fl at surfaces
Place the main unit indoors and the remote sensor
outdoors. Place them on fl at surfaces using their
respective stands (included).
outdoors. Place them on fl at surfaces using their
respective stands (included).
wall mounting
1. Select an indoor wall for your main unit and an
outdoor wall for your remote sensor.
2. Remove the stands from the main unit and
remote sensor, respectively.
2. Drill a hole in the wall.
3. Thread a screw (not supplied) into the hole,
letting it extend about 3/16” from the wall.
4. Fit the head of the screw into the appropriate
keyhole slot.
Thank you for purchasing your Large Display Wireless
Indoor/Outdoor Thermometer from RadioShack. You can
mount it on a wall or place it on a fl at surface using the
included stand. Your thermometer can collect and display
indoor and outdoor temperature and humidity readings
from up to three sensors, and forecast weather.
Indoor/Outdoor Thermometer from RadioShack. You can
mount it on a wall or place it on a fl at surface using the
included stand. Your thermometer can collect and display
indoor and outdoor temperature and humidity readings
from up to three sensors, and forecast weather.
main unit and stand
remote sensor
user’s guide
wire stand
63-1090
large display wireless
indoor/outdoor thermometer
Please read this user’s guide before
installing, setting up and using your new product.
www.radioshack.com
SNOOZE
MODE
Use to change the
display and settings.
Use to change the
display and settings.
and
Increase or decrease
setting and activate or
deactivate the Atomic
Clock.
Increase or decrease
setting and activate or
deactivate the Atomic
Clock.
((•))
Set alarm or view alarm
status.
Set alarm or view alarm
status.
Turn alarm on or silence
it for 24 hours.
CHANNEL
Switch remote sensors.
Switch remote sensors.
MEMORY
View current, maximum,
and minimum
temperature and
humidity readings.
View current, maximum,
and minimum
temperature and
humidity readings.
PRESSURE
Change pressure
measurement units.
Change pressure
measurement units.
°C/°F
Select temperature
units.
Select temperature
units.
Weather Forecast and
Barometric Trend Area
Barometric Trend Area
Outdoor Temeprature
and Humidity Area
and Humidity Area
Indoor Temperature and
Humidity Area
Humidity Area
Clock and Alarm Area
The main unit requires three AA alkaline batteries
and the remote sensor requires two AAA alkaline
batteries for power. None are supplied; all are
available at RadioShack or online at
www.radioshack com.
and the remote sensor requires two AAA alkaline
batteries for power. None are supplied; all are
available at RadioShack or online at
www.radioshack com.
For best results, always install batteries
in the remote sensor fi rst, and then in the
main unit.
in the remote sensor fi rst, and then in the
main unit.
1. Remove the battery compartment covers from the
main unit and remote sensor, respectively. If you are
using more than one sensor, select a different channel
for each sensor by switching CHANNEL 1 2 3.
using more than one sensor, select a different channel
for each sensor by switching CHANNEL 1 2 3.
2. Place the appropriate batteries in each compartment,
following the polarity symbols (+ and -) marked
inside.
inside.
3. Reset each unit and replace the battery compartment
covers.
RESET
RESET
Stand
Keyhole
Slot
This clock shows the current time and the day
of week in English, French, German, Italian,
or Spanish. The US Atomic Clock in Boulder,
Colorado, automatically updates the information
when the main unit is within 932 miles of a signal.
Initial reception takes 2—10 minutes. It is initiated
when you fi rst set up the unit and whenever you
press RESET. Once complete, the reception icon
will stop blinking.
of week in English, French, German, Italian,
or Spanish. The US Atomic Clock in Boulder,
Colorado, automatically updates the information
when the main unit is within 932 miles of a signal.
Initial reception takes 2—10 minutes. It is initiated
when you fi rst set up the unit and whenever you
press RESET. Once complete, the reception icon
will stop blinking.
1. Press and hold MODE for 2 seconds. The time
zone blinks.
2. Press MODE to select the time zone, hour,
minute, year, month, day, and language. Press
or to set your desired setting. Press
MODE to confi rm.
MODE to confi rm.
• The language options are E (English),
F (French), D (German), I (Italian), and
S (Spanish).
S (Spanish).
• The time zone options are PA (Pacifi c),
CE (Central), MO (Mountain), and EA (Eastern).
• Press MODE to toggle between Clock with
Seconds and Clock with Weekday display.
NOTE
CHANNEL 1 2 3
NOTE