Seagate ST336732LW/LC プリント
Figure 2.
Option select jumpers.
4.
Connect the Drive Activity LED (optional)
Connect the Drive Activity LED cable to J6 pins 11 and 12, or connect a
drive ID and Drive Activity LED cable to J5, depending on the host system.
drive ID and Drive Activity LED cable to J5, depending on the host system.
5.
Check the other available jumper settings
Select other options on J2 as illustrated in Figure 2. Do not change these
unless instructed to do so by the host system documentation.
unless instructed to do so by the host system documentation.
6.
Mount the drive in the host system and connect cables
Note. LC drives are designed to be attached to a carrier or tray and
inserted into the host system without I/O or power cables.
a.
Mount LW drives to the chassis using four 6-32 UNC screws. Two
mounting holes are in each side of the drive and there are four
mounting holes in the bottom of the drive. Do not over-tighten or
force the screws. You can mount the drive in any orientation.
mounting holes are in each side of the drive and there are four
mounting holes in the bottom of the drive. Do not over-tighten or
force the screws. You can mount the drive in any orientation.
b.
Connect the SCSI I/O cable into the drive’s SCSI connector. Take
care not to stretch or crimp this cable, and do not block the system’s
cooling air flow with the cable.
care not to stretch or crimp this cable, and do not block the system’s
cooling air flow with the cable.
Note. For Ultra2 and faster operation, special twisted pair LVD
cables are
required
.
c.
Connect the DC power cable to the drive. See Figure 3.
Figure 3.
Cable connections and external termination
7.
Format the drive
The drive has been
low level
formatted at the factory. You do not need to
perform another low level format on this drive unless you decide to perform
certain diagnostics through the host adapter. If you do decide to perform a
low level format, do not abort the format as this is likely to make the drive
inoperable. A low level format, with verify turned on, may take two hours.
certain diagnostics through the host adapter. If you do decide to perform a
low level format, do not abort the format as this is likely to make the drive
inoperable. A low level format, with verify turned on, may take two hours.
Protect against power failure or other power interruptions during the format.
a.
Turn on DC power to the host system and boot the system from a
system floppy, CD, or from a previously installed hard disc drive if
there is one.
system floppy, CD, or from a previously installed hard disc drive if
there is one.
b.
Format the drive.
Caution. Formatting a drive erases all user data. It is not necessary to for-
mat a drive that previously has been used to store data, unless
your intention is to erase all user data. Seagate
your intention is to erase all user data. Seagate
®
is not responsi-
ble for lost user data.
Cheetah X15 36LP disc drives are designed to operate with a variety of
operating systems. Please refer to your system or SCSI controller manual
for information about formatting and setting up the drive. Some quick desk-
top system notes are provided below.
operating systems. Please refer to your system or SCSI controller manual
for information about formatting and setting up the drive. Some quick desk-
top system notes are provided below.
• Microsoft
TM
. Set the drive type in CMOS to “
Zero,” “None,”
or “
No hard
drive installed
.” Use FDISK.EXE and FORMAT.EXE. Systems using Win-
dows 98 or later can create one single partition (drive letter) on the drive.
• Macintosh
TM
. Mac OS 8.6, 9.x and OS X: Use Apple’s Drive Setup utility
to partition and initialize the drive. Mac OS 8.5 or earlier: Use a third-
party drive utility. For more information, refer to: www.apple.com.
party drive utility. For more information, refer to: www.apple.com.
Troubleshooting
• Drive does not spin up. Check cables and all jumper settings. Make
sure cable pin 1 (edge stripe) matches PCB pin 1.
• Drive spins, but no LED on/off activity. Check SCSI ID setting. Set the
ID so that each device on the SCSI chain has its own unique ID. See also
the next item below. The host I/O controller is usually ID7.
the next item below. The host I/O controller is usually ID7.
• Computer does not seem to recognize the drive. Verify that the drive
is enabled by the SCSI host adapter setup utility.
• FDISK does not detect the drive. Run the FDISK program located on
your Windows startup diskette. Type fdisk/status to verify that your hard
drive is present.
drive is present.
Seagate support services
For online information about Seagate products, visit www.seagate.com or
e-mail your disc questions to DiscSupport@Seagate.com.
e-mail your disc questions to DiscSupport@Seagate.com.
If you need help installing your drive, consult your dealer first. If you need
additional help, call a Seagate technical support specialist. Before calling,
note your system configuration and drive model number
additional help, call a Seagate technical support specialist. Before calling,
note your system configuration and drive model number
.
Africa
+31-20-316-7222
New Zealand
0800-443988
Australia
1800-14-7201
Norway
800-113 91
Austria
0 800-20 12 90
Poland
00 800-311 12 38
Belgium
0 800-74 876
Spain
900-98 31 24
Denmark
80 88 12 66
Sweden
0 207 90 073
France
0 800-90 90 52
Switzerland
0 800-83 84 11
Germany
0 800-182 6831
Singapore
800-1101-150
Hong Kong
800-90-0474
Taiwan
+886-2-2514-2237
India
1-600-33-1104
Thailand
001-800-11-0032165
Indonesia
001-803-1-003-2165
Turkey
00 800-31 92 91 40
Ireland
1 800-55 21 22
United Kingdom 0 800-783 5177
Italy
800-790695
USA/Canada/
1-800 SEAGATE or
Malaysia
1-800-80-2335
Latin America
+1-405-936-1234
Middle East +31-20-316-7222
Other European
Netherlands 0 800-732-4283
countries
+31-20-316-7222
Warranty. Contact your place of purchase or our web site (above).
Return Merchandise Authorization (RMA).
Before returning the drive, verify that it
is defective. Seagate Worldwide customer service centers are the only facilities autho-
rized to service Seagate drives. Contact nearest center for return procedures and trade
regulations.
rized to service Seagate drives. Contact nearest center for return procedures and trade
regulations.
Shipping the drive
Caution.
Caution.
Back up the data before shipping. Seagate assumes no responsibility for
data lost during shipping or service. Shipping drive in an unapproved container voids
the warranty. Pack the drive with original box and packing materials. Use no other
materials. This prevents electrical and physical damage in transit.
the warranty. Pack the drive with original box and packing materials. Use no other
materials. This prevents electrical and physical damage in transit.
© 2002 Seagate Technology LLC All rights reserved
Publication number: 100139875, Rev. C, June 2002, Printed in U.S.A.
Seagate, Seagate Technology, the Seagate Logo, and Cheetah are either registered
trademarks or trademarks of Seagate Technology LLC. All other trademarks are the
property of their respective owners.
trademarks or trademarks of Seagate Technology LLC. All other trademarks are the
property of their respective owners.
J2
Pin 1
No Connection
Write protect = Off (enables writing).
Write protect = On (disables writing).
Write Protect option
Pin 1
SCSI I/O
Connector
Drive with
HDA up, PCB
down, viewed
down, viewed
from front
Pin 1
DC Power
Connector
Connector
J2
Drive Front
J6
Pin 1
HDA
J6
A2
A3
A1 A0
Reserved
Remote
LED
LED
L
E
E
D
R
E
S
E
S
Reserved
Shipped with cover installed.
Do not remove.
Do not install jumpers
on these four positions.
CATH
11
12
(default)
Single-ended I/O
Forces single-ended operation.
Allows the host to select either
single-ended or LVD operation.
single-ended or LVD operation.
(default)
LC Models
J2
Pin 1
LW Models
Single-ended I/O
Forces single-ended operation.
Allows the host to select either
single-ended or LVD operation.
single-ended or LVD operation.
(default)
Delay Motor Start
(valid only if the Remote Motor
Start jumper is not connected).
(valid only if the Remote Motor
Start jumper is not connected).
Disable Delay Motor Start.
Motor start delay equal to the
SCSI ID multiplied by 12 seconds.
SCSI ID multiplied by 12 seconds.
(default)
Remote Motor Start
Disable Remote Motor Start. The
drive starts according to the Delay
Motor Start option.
drive starts according to the Delay
Motor Start option.
Enable Remote Motor Start. The
drive waits for the Start Unit
command from the host before
starting the spindle motor.
drive waits for the Start Unit
command from the host before
starting the spindle motor.
(default)
Write Protect
Write Protect = Off (enables writing)
Write Protect= On (disables writing)
(default)
Parity Check
Enable parity check
Disable parity check
(default)
Terminator Power
Termination power to SCSI bus.
Host adapter or other device
provides termination power to
external terminator.
provides termination power to
external terminator.
(default)
No Connection
Pin 1
(check your
adapter for
Pin 1 location)
Host
Adapter
PCB
Twisted Pair
LVD Cable
Ultra320, Ultra160 or Ultra2 LVD bus segment
SPI-2 compliant
active LVD
external terminator
on the end of
the cable
SCSI
LVD/SE
SCSI
SE
Ultra SCSI SE bus segment