Seagate ST320011A プリント

 

DiscWizard



 is Seagate’s exclusive Windows program that is included with

your drive for easy drive installation. You can use this software if you have a
bootable hard drive in your computer and are running

 

Windows Me,

Windows 98 or Windows 95. Download the software from our Web site at
www.seagate.com.

Run DiscWizard 

before 

installing your drive for customized step-by-step

instructions for your system.

To run DiscWizard:

Download the software from www.seagate.com, and follow the online
instructions to complete the installation.
If you cannot run DiscWizard, follow the instructions on this installation
sheet to install and configure your drive.

•

 A Phillips screwdriver and four 6-32 UNC drive mounting screws

•

 A standard 40-pin ATA interface cable, 

or

 an 80-conductor cable to run

Ultra ATA 100 (max length: 18 inches)

•

 An unused drive power cable for your new drive

•

 A version of Windows with FAT32 file system for drives over 32 Gbytes

The drive can be configured to support a default maximum transfer rate.
This drive can support transfer rates up to 100 Mbytes per second
(UDMA 5) in Ultra ATA/100 mode. Using a software utility, you can set the
default transfer rate to the best capability of your system. For your drive to
run in this mode, you need the following:

•

 A computer that supports UDMA mode 5

•

 A 40-pin 80-conductor cable (available from your dealer)

•

 A software utility to confirm and activate Ultra ATA/100. Seagate

®

 provides

a utility called UATA100.exe. You can download the latest version from our
Web site at  www.seagate.com.

•

 Windows Me or Windows 98 operating system: either supports Ultra

ATA\100.

Disc drives are extremely fragile.

 Do not 

drop or jar the drive.

Keep the drive in the protective SeaShell



 container until you are

ready to install it. This minimizes handling damage.

The drive has a protective cover called SeaShield

®

. Do not remove

this permanent cover—it protects the drive from electrostatic
discharge (ESD) and minor impact damage.

Protect your drive from static discharge by wearing a grounded wrist
strap throughout the installation process.

Always handle the drive by the edges or frame.

Do not apply pressure or attach labels to the circuit board or the
top of the drive.

Refer to the jumper settings
on your drive label to
configure the drive for your
system. Jumper settings also

can be accessed online from
our Web site at
www.seagate.com.

*Drives may be shipped with
either configuration as default.

•

 Master or single drive: To configure the drive as a master or a single

drive, set the jumper on pins 7 and 8.

• 

Drive is slave: To configure the drive as a slave, or second drive on

the cable, remove all the jumpers.

• 

Master with non ATA-compatible slave: Use this setting if the slave

drive is not recognized. Configure the master drive with a jumper set on
pins 5 and 6 and pins 7 and 8 to enable this option.

• 

Cable select option: Cable Select jumpers use the cable to determine

master or slave. To enable cable select, set a jumper on pins 5 and 6. If
using two drives, jumpers for both drives should be set on pins 5 and 6.

• 

Alternate capacity jumper:  Drives with a 40-Gbyte capacity and

greater are limited to 32 Gbytes. This jumper is used to provide a
solution to specific legacy BIOS problems. When using the alternate
capacity jumper, Disk Manager software is required to achieve the
drive’s full capacity.

1.  Attach one end of the drive interface cable to the interface connector

on your computer’s motherboard

 

(see your computer manual for

connector locations).

 Caution.  Align pin 1 on the motherboard connector with pin 1 on

your drive connector. Pin 1 is marked by a stripe on one side of the cable.

2. Attach the interface connector and the power connector to the drive.

Note. You can mount the drive in any orientation. Usually it is mounted

      with the circuit board down.

3.  Secure the drive in the computer using four 6-32 UNC mounting

screws in either the side-mounting or bottom-mounting holes. Insert
the screws no more than 0.20 inch (5.08 mm) into the bottom-mounting
holes and no more than 0.14 inch (3.55 mm) into the side-mounting holes.

 Caution. Do not overtighten the screws or use metric screws. This

may damage the drive.

For your computer to recognize your new drive, configure your
computer’s BIOS as follows:

1. Run the system setup program.

2. Enable LBA mode and UDMA mode, if available.

3. Select the auto-detect option. If necessary, refer to the drive param

eters on your drive label to configure the drive for your system. BIOS
settings can also be accessed at  www.seagate.com. To access the full
capacity of the drive, use LBA mode or use Disk Manager.

4. Save and exit the system setup program.

ST380021A

80.0

156,301,488

ST360021A

60.0

117,231,408

ST340016A

40.0

78,165,360

ST320011A

20.0

39,102,336

*One sector equals 512 bytes.

Pin 1

Interface
connector

Power
connector

Note.  When configuring two ATA devices on

the same cable, both must use Cable 
Select or both must use Master/Slave 
jumper settings. If using a standard 
40-pin cable, the master and slave 
drives can be placed in any position. If 
using a 40-pin 80-conductor cable, attach
the blue connector to the motherboard, 
the black connector to the master drive 
and the grey connector to the slave.

Computer

Motherboard

Pin 1

Circuit Board

2

6

8

4

1

7

5

3

Drive is slave

*Master or single drive 

*Cable select 

Master with non ATA-
compatible slave

Limit drive capacity
>32 Gbytes = 32 Gbytes
<32 Gbytes = 2.1 Gbytes