Frigidaire FGHS2367KE ユーザーズマニュアル

18

Visit our web site at

1-800-944-9044 (United States)

1-800-265-8352 (Canada)

Ice maker wire signal arm is in 

•

the “up” or OFF position.

Ice maker power switch is Off.

•

Ice maker has small cube 

•

caught in mechanism.

Saddle valve on cold water 

•

pipe is clogged or restricted by 

foreign material.

Move wire signal arm to the “down” or 

•

ON position. (side 

mounted)

Turn power switch to On (“

•

I”) position. (rear mounted)

Remove small cube from ice maker.  The ice and water 

•

filter cartridge may be clogged. Replace filter cartridge.

Turn off household water line valve.  Remove valve.  En-

•

sure that valve is not a self-piercing saddle valve.  Clean 

valve.  Replace valve if necessary.

Ice maker is producing less ice 

•

than you expect.

Check to see if water dispenser 

•

is dispensing slower than normal.

Side mounted ice maker should produce 4 to 4.5 pounds 

•

(approximately 4 quarts) of ice every 24 hours.  A rear 

mounted ice maker should produce 3 to 4 pounds (ap-

proximately 3½ quarts) of ice every 24 hours.  Quick Ice 

option should produce up to 50% more ice every 24 hours.

If it is, replace the ice and water filter cartridge.

•

Ice maker wire signal arm is 

•

being held down by some item 

in the freezer.

Move item and release wire signal arm.  Remove any ice 

•

cubes that are frozen together over the wire signal arm.

Ice cubes are not being used 

•

frequently enough.

Ice cubes are hollow (partially 

•

frozen cubes with water inside).

Freezer control is set too warm.

•

Remove ice container and discard ice from container.  Ice 

•

maker will produce fresh supply.

The ice and water filter cartridge may be clogged. Replace

•

filter cartridge.

Set freezer control to colder setting.  Allow 24 hours for 

•

temperature to stabilize.

Ice storage container is empty.

•

Freezer temperature is set too 

•

warm.

Household water line valve is 

•

not open.

Ice dispensing arm has been held 

•

in for more than 4-5 minutes.

When the first supply of ice is dropped into the container,

•

the dispenser should operate.

Turn freezer control to a higher setting so that ice cubes 

•

will be made. When first supply of ice is made, dispenser

should operate.

Open household water line valve. Allow sufficient time

•

for the ice to be made.  When ice is made, the dispenser 

should operate.

Motor is overloaded.  Motor over load protector will reset in 

•

approximately 3 minutes.  Ice can then be dispensed.

Ice has melted and frozen 

•

around auger due to infrequent 

use, temperature fluctuations,

and/or power outages.

Ice cubes are jammed between 

•

ice maker and back of ice 

container.

Remove ice container, thaw, and empty the contents.  

•

Clean container, wipe dry, and replace in proper position.  

When new ice is made, dispenser should operate.

Remove ice cubes that are jamming the dispenser.

•

Door was closed too hard, caus-

•

ing other door to open slightly.

Refrigerator is not level.  It 

•

rocks on the floor when moved

slightly.

Refrigerator is touching a wall 

•

or cabinet.

Close both doors gently.

•

Ensure floor is level and solid, and can adequately support

•

the refrigerator.  Contact a carpenter to correct a sagging 

or sloping floor.

Ensure floor is level and solid, and can adequately support

•

the refrigerator.  Contact a carpenter to correct a sagging 

or sloping floor.

Food is touching shelf on top of 

•

drawer.

Track that drawers slide on is 

•

dirty.

Remove top layer of items in drawer.

•

Ensure drawer is properly installed on track.

•

Clean drawer, rollers, and track.  See 

•

Care & Cleaning.