KitchenAid 1855 ユーザーズマニュアル
exhaust hood Duct location
Figure 3 shows exact center of duct for both four & six burner
ranges. Cut drywall opening 10 1/4” x 3 3/8”.
Height from floor to center of duct on all installations should
Height from floor to center of duct on all installations should
be 62 1/4”=D.
Note: Electrical receptacle & gas piping should be located in
Note: Electrical receptacle & gas piping should be located in
center of opening 6” off floor.
Important: If you have purchased the short leg option, D
Important: If you have purchased the short leg option, D
dimension will be 60 1/4”.
installing your exhaust hooD
Your elmira range is equipped with a 350 CFM exhaust
fan located in the warming cabinet. This fan can be vented
directly to the outside or, with the use of the #1442 Charcoal
Filter (included) can recirculate purified exhaust air into the
room.
Charcoal filter should be changed every six months.
See page 20 for Filter Cleaning and Replacement.
fan located in the warming cabinet. This fan can be vented
directly to the outside or, with the use of the #1442 Charcoal
Filter (included) can recirculate purified exhaust air into the
room.
Charcoal filter should be changed every six months.
See page 20 for Filter Cleaning and Replacement.
Ventless installation
Remove the charcoal filter from the broiler pan and
remove plastic wrap. Remove the two screws holding
the mesh filter in place with a #2 phillips or red square
screw driver. Insert the charcoal filter into mesh filter and
replace the assembly. See figure 4
remove plastic wrap. Remove the two screws holding
the mesh filter in place with a #2 phillips or red square
screw driver. Insert the charcoal filter into mesh filter and
replace the assembly. See figure 4
Figure 4
To increase efficiency of the charcoal filter system, fan air
should blow against the 45 degree vent deflector at rear of
stove.
should blow against the 45 degree vent deflector at rear of
stove.
Vented installation
• Remove vent deflector on rear of stove if venting to the
outside and seal screw holes.
• If the exhaust hood is to be vented, the duct location
must be installed in accordance with figure 3, page 7.
Exhaust air must not be vented into a wall, ceiling, attic
or a concealed space of a building.
Exhaust air must not be vented into a wall, ceiling, attic
or a concealed space of a building.
note: Installation must be in accordance with local
and national building codes. Use only materials which
conform to codes in effect.
and national building codes. Use only materials which
conform to codes in effect.
Disconnect power before
doing any electrical work. Use only metal ducting, do
not use plastic. Assemble securely so that in the event of
a grease fire, the fire will be contained within the metal
ductwork.
Never vent exhaust air into a wall, attic, ceiling or any
concealed space of a building, as an accumulation of
grease could pose a fire hazard. Dampers on vented hoods
must open freely and no obstruction should block the
discharge opening.
Important: If you have purchased the optional in-line
blower, see installation instructions with blower.
not use plastic. Assemble securely so that in the event of
a grease fire, the fire will be contained within the metal
ductwork.
Never vent exhaust air into a wall, attic, ceiling or any
concealed space of a building, as an accumulation of
grease could pose a fire hazard. Dampers on vented hoods
must open freely and no obstruction should block the
discharge opening.
Important: If you have purchased the optional in-line
blower, see installation instructions with blower.
8
44 1/4"
Duct
Nickel Rail
Nickel
Rail
15 3/8"
68 1/4"
64 1/4"
62 1/4"
BACK VIEW
OF RANGE
G
C
D
M
N
28 1/2"
I
30 1/8"
A
29 1/2"
L
37 3/8"
F
36 3/8"
E
68 1/4"
N
64 1/4"
M
30 1/2"
BACK VIEW
OF RANGE
Nickel Rail
29 1/2"
68 1/4"
64 1/4"
62 1/4"
Duct
15 3/8"
H
B
C
D
M
N
Figure 3