Vertex Standard FT-2000 ユーザーズマニュアル
Page 87
FT-2000 O
PERATING
M
ANUAL
C
ONTEST
M
EMORY
K
EYER
C
HECKING
THE
CW M
EMORY
C
ONTENTS
1. Be sure that Break-in is still turned Off by the [BK-IN]
button.
2. Press the [MONI] button to enable the CW monitor.
3. Press the [F1(CH1)] ~ [F4(CH-4)] button to check
3. Press the [F1(CH1)] ~ [F4(CH-4)] button to check
your work. You will hear the results in the sidetone,
but no RF energy will be transmitted.
but no RF energy will be transmitted.
N
OTE
:
Adjust the monitor level using the [MONI] knob.
[F1(CH-1)] ~ [F4(CH-4)] Button
[BK-IN] Button
TEXT
!
“
”
”
#
$
%
&
‘
’
’
DISPLAY
CW CODE
SN
AF
---
SX
KA
AS
WG
TEXT
(
“
)
”
*
+
,
---
.
DISPLAY
CW CODE
KN
KK
---
AR
MIM
DU
AAA
TEXT
/
“
:
”
;
<
=
>
?
DISPLAY
CW CODE
DN
OS
KR
---
BT
---
IMI
TEXT
@
“
[
”
\
]
^
_
‘
}
’
DISPLAY
CW CODE
@
---
AL
---
---
IQ
---
O
N
-T
HE
-A
IR
CW M
ESSAGE
P
LAYBACK
1. Press the [BK-IN] button to enable transmission. Ei-
ther Full- or Semi-break-in will be engaged, depend-
ing on the setting of Menu item “058 A1A BK-IN.”
ing on the setting of Menu item “058 A1A BK-IN.”
2. Press the [F1(CH1)] ~ [F4(CH-4)] button to transmit
the programmed message.
N
OTE
:
If you subsequently decide to use the “Message Memory”
technique for memory storage, please note that the con-
tents of a message stored using text input will not be trans-
ferred over when you select “Message Memory technique”
on a particular memory register (the Menu Mode Setting
is set to “tyP2”).
technique for memory storage, please note that the con-
tents of a message stored using text input will not be trans-
ferred over when you select “Message Memory technique”
on a particular memory register (the Menu Mode Setting
is set to “tyP2”).
[F1(CH-1)] ~ [F4(CH-4)] Button
[BK-IN] Button
Contest Number Programming
Use this process if you are starting a contest, or if
you somehow get out of sync with the proper num-
ber in the middle of a contest.
you somehow get out of sync with the proper num-
ber in the middle of a contest.
1. Press the [MENU] button to enter the Menu
mode.
2. Rotate the Main Tuning Dial knob to select
Menu item “019 tEy CONTEST.”
3. Rotate the [SUB VFO-B] knob to set the Con-
test Number to the desired value.
Advice:
Press the [CLEAR] button (located below and
to the left of the [CLAR] knob) to reset the Con-
test Number to “1.”
Advice:
Press the [CLEAR] button (located below and
to the left of the [CLAR] knob) to reset the Con-
test Number to “1.”
4. Press and hold in the [MENU] button for two
seconds to store the new number and exit to
normal operation.
normal operation.
Decrementing the Contest Number
Use this process if the current contest number gets
slightly ahead of the actual number you want to
send (in case of a duplicate QSO, for example).
slightly ahead of the actual number you want to
send (in case of a duplicate QSO, for example).
Press the [F6(DEC)] button on the front panel. The
current Contest Number will be reduced by one.
Press the [F6(DEC)] button as many times as nec-
essary to reach the desired number. If you go too
far, use the “Contest Number Programming” tech-
nique desired above.
current Contest Number will be reduced by one.
Press the [F6(DEC)] button as many times as nec-
essary to reach the desired number. If you go too
far, use the “Contest Number Programming” tech-
nique desired above.
CW C
ONVENIENCE
F
EATURES