Zooper BU806A プリント

Do not fold your stroller when wet.
Machine wash removable seat and armrest covers using gentle cycle, 
cold water, and a mild detergent. The canopy can only be spot washed.
Line dr y fabric parts. 
Never use bleach when washing.
Do not leave your stroller in direct sunlight for extended periods of time.
Clean and lubricate all moving parts on the stroller frame and wheels 
as needed. Use only a penetrating silicon based lubricant.   
Regularly check for loose screws, broken parts, etc. Use only Zooper 
approved replacement parts available through the service centers listed below. 
Wipe off any sand, salt or other corrosive residue after each use where the stroller 
may be exposed to those elements. 

In order to maintain the highest quality standards, the distributor  reserves the 
right to improve or alter any Zooper stroller design without notice or obligation to 
any previous purchaser. For questions or service needs, please contact the 
service center located in your countr y of residence. Sending in your warranty 
card will help expedite any service needs.

MAINTENANCE

IMPORTANT CARE AND SAFETY INFORMATION

IMPORTANT: READ THESE SAFETY INSTRUCTIONS CAREFULLY BEFORE USING 
YOUR STROLLER AND KEEP THEM FOR FUTURE REFERENCE. THE SAFETY OF 
YOUR CHILD DEPENDS ON IT.

Thank you for choosing Zooper. 

UNLOCKING & OPENING THE FRAME

Bolero BU806A/B

Avoid serious injur y from falling or sliding out, always use safety harness provided.
Always engage the rear brakes when not holding onto your stroller.
Never leave your child unattended.
Never use the stroller near an open fire or exposed flame.
Never allow the stroller to be used as a toy.
Never allow more than one child at a time in the stroller.
Never hang bags or other items from the handle or on the canopy. This may 
cause the stroller to become unstable.
Never use the stroller on stairs or escalators.
Do not overload the basket. Maximum load is 7 lbs. Excessive weight may cause 
a hazardous unstable condition to exist.
Do not overload the canopy pocket: Maximum load is 2 lbs. Excessive weight 
may create a hazardous unstable condition to exist.
Before each use, check to make sure the stroller is set up properly and that all the 
wheels are properly and securely attached.
This stroller is not recommended for use with a child over 55 lbs. 
This stroller is designed as a walking stroller. We do not recommend running, 
roller blading, or other such activities with this stroller.
This stroller is a single stroller  do not use any attachments that allow for a second 
child.
It may be unsafe to use accessories other than those approved by the 
manufacturer or distributor.

To open the stroller, first lift up on the black colored 
frame lock located on the right side of the stroller, 
(Fig.1). Be sure the frame lock detaches from the metal 
locking pin. Then pull up on the main stroller handle 
while pushing down with your foot on the plastic tab 
located between the wheels (Fig.2)Using your hand, 
push down on the front edge of the seat to ensure the 
stroller frame has locked properly in the open position. 
Do not push down on the front armrest bar. 

 

Be sure children are at a safe 

distance and cannot reach moving parts whenever 
opening or closing the stroller. 

ATTACHING THE FRONT WHEELS 
TO THE FRAME

Press each wheel block firmly onto the metallic tube 
ends until they "click" into position (Fig.3). Check to see 
they have been properly installed by pulling down on 
the wheel block. To remove the front wheels, push the 
metal lock located just above the plastic housing and 
then pull the housing off the metal tubes. 

Fig.1

Fig.2

Fig.3

ATTACHING THE REAR WHEELS TO 
THE FRAME

Insert both plastic rear wheel housings onto the rear 
leg tubes of the stroller (Fig.4). Make sure the brake 
levers are facing out, away from the stroller. Then push 
in each locking spring located on the rear stroller 
tubes. Holding the locking pin in, slide each wheel 
block over the pin until it locks into place and the silver 
head of the locking pin can be seen protruding from 
the wheel housing (Fig.5).
To remove the rear wheel assembly, push in on the 
locking pins while pulling down on each wheel block.

Do not use the stroller if the brake 

levers are not facing away from the stroller and if the 
locking pins are not visible as described above. 
Contact the appropriate service center listed at the 
back of these instructions if you have questions.

ADJUSTING THE SEATBACK

To lower the backrest, lift up on the plastic lever 
located in the middle of the seatback. While holding 
the lever up, move the seatback down into desired 
position and then release the lever (Fig.6). To raise the 
backrest, push up on the back of the seat until it clicks 
into the desired position.

Always keep your child in sight 

when making these kinds of adjustments. Check the 
fitting of the  safety harness each time the backrest is 
adjusted to be sure a  snug, yet comfortable fitting is 
maintained.

USING THE BRAKES

To set the brakes step down on both left and right rear 
wheel brake levers. Push forward slightly to ensure both 
brakes have engaged. To release the brakes push the 
brake levers back inward toward the stroller so that 
they are parallel with the rear leg tubes.(Fig.7)

      WARNING: 

Always engage both rear brakes 

whenever not holding onto the stroller. Never leave 
Your child unattended. Do not leave stroller near 
dangerous places such as stairs, curbs, etc.

Fig.4

Fig.5

Fig.6

Fig.7

ATTACHING THE FRONT BAR TO THE 
ARMRESTS

To attach the front armrest to the stroller seat, line up 
the inserts of the armrest bar with the two plastic slots on 
both sides of the stroller.  Slide the inserts completely 
into these slots, making sure that both sides secure into 
a locked position.  Pull out on each side of the armrest 
to make sure that the armrest is properly locked into the 
slots.  The armrest should not release from the slots.  To 
remove the armrest, locate the plastic tabs underneath 
where the armrest connects to the sides of the stroller.  
Press in the tabs while pulling up on the armrest.

Never pick the stroller up by the 

front armrest.To avoid serious injur y, ensure that 
children's hands, arms and feet are well clear of the 
bumper bar before opening or closing it.

ENCLOSING THE SEAT WHEN THE 
BACKREST IS FULLY RECLINED

The seating area must be fully enclosed whenever the 
seat is in a fully reclined position. To do so, rotate the 
footrest back so that it is parallel with the side armrests. 
Then zip both sides of the footrest to the zipper track on 
the sides of the seat. (Fig.9)

Your child may slip into leg 

openings and strangle. Never use the stroller with the 
backrest fully reclined unless this seat area is fully 
enclosed.

ATTACHING THE CANOPY

To attach the canopy, insert the plastic shafts into the 
plastic slots located on the outside of the main stroller 
tubes (Fig 10). They are inserted from the bottom up.
Lift up to check that each side is locked into position. 
Open the canopy by pushing down on the plastic side 
canopy braces. Be sure to snap the canopy to 
the seat and backrest fabric whenever the seat is fully 
reclined. Retract the canopy by first pulling up on the 
side braces, then pushing the canopy hood back. 
The canopy can be converted to allow more air flow 
through the stroller. Unzip thelower half of the canopy 
from the upper half. This will leave a mesh cover that 
can snap to the back of the seat. To remove the 
canopy, first undo the snaps. Then pull the release tabs 
outward and slide the canopy down, off the slots. 

The rear panel of the canopy must 

be snapped  onto the seat whenever the seat is fully 
reclined.

Fig.8

Fig.9

SAFETY HARNESS

Zooper provides a special 5-point harness safety system. 
Used properly, this harness will keep your child seated 
and safe. To secure your child in the harness, push 
buckles (A) and (B) into the buckle housing (C) until the 
buckle prongs snap into position. Carefully adjust slider 
(D) to fit snugly and comfortably around your child see 
(Fig 11).Follow the same procedure to adjust the 
shoulder straps. Always re-tighten the harness when your 
child is in a sit up or lay back position.

SECURING AN INFANT CARRIER (JUST 
FOR SL806A)

To install an infant carrier, first be sure that the infant 
carrier is not attached to its permanent car base. 
Locate the car seat adapter strap that was packaged 
with your stroller. It should have a buckle in the center, 
and a clip on each end. Next, identify the D-rings 
located in the hip points of the stroller seat. Ensure that 
infant seat has been removed from its permanent car 
base.
Step 1: Recline the stroller seat to the 3rd or 4th position. 
Step 2: Attach the car seat adapter strap to the stroller   
             seat by clipping the ends to the D-rings. Adjust 
             the strap so that it is fully extended. Unbuckle the   
             Center, and  lay the ends out over the armrests 
             of the stroller seat. 
Step 3: Place the infant seat into the stroller seat, so that 
             the infant seat is facing the parent. Depending 
             on the size and design of your seat, you will either 
             place it inside the bumper bar, or over the   
             bumper bar.
Step 4: Bring the ends of the adapter strap back over the 
             infant seat, and buckle the center. The belt 
             should be positioned so that it travels over the 
             lap of the infant seat. Some models have belt 
             guides located on the sides, if your model does;  
             make sure the strap is positioned inside these 
             guides.
Step 5: Tighten the strap down so that infant seat is 
             securely fixed into the stroller seat. Infant seat 
             should not lift out of the stroller seat if properly 
             Strapped in.

Only the following infant car seat 

models are compatible with this stroller: Graco Snugride, 
Graco Safeseat, Britax Companion, and Evenflo On My 
Way

FOLDING THE STROLLER

Each time, before closing your stroller, check the 
following:

  

Set the stroller brakes

   Retract the canopy
   Move the seatback into the upright position
   Make sure there is nothing in the shopping basket
   Push in on the main frame lock button located in the      
   middle of the stroller handle.
   Push the handle down in the middle until it stops in a   
   “ V ” shape.
   Pull up on the base frame handle located at the top 
   of the cross bars which connect both rear leg tubes.    
   Pull this handle up toward you until the stroller fully   
   Closes and the right side auto frame lock engages.

Fig.12

PRESS

PUSH

PULL

Shoulders

Straps

Fig.11

Fig.13

 

 

 

Fig.10