Zooper SL808 プリント

ATTACHING THE CANOPY

To attach the canopy, insert the plastic shafts into the 
plastic slots located on the outside of the main stroller 
tubes (Fig 9). Lift up to check that each side is locked 
into position.  Open the canopy by pushing down on 
the plastic side canopy braces. Be sure to snap the  
canopy to the seat and backrest fabric whenever the 
seat is fully reclined. Retract the canopy by first pulling 
up on the side braces, then pushing the canopy hood 
back. The canopy can be converted to allow more air 
flow  through the stroller. Unzip the lower half of the 
canopy  from the upper half. This will leave a mesh 
cover that can snap to the back of the seat.“The 
canopy may also be used as a napper canopy. 
Locate the zipper on the rear rib of the canopy. 
When unzipped the canopy will fall forward over the 
bumper bar, completely shading baby from the world. 
To remove the canopy,first undo the snaps. Then press
in the release tabs, located on the plastic slots, 
while pulling up on the canopy shafts. 

    WARNING

The rear panel of the canopy must 

be snapped  onto the seat whenever the seat is 
fully reclined.

Zooper provides a special 5-point harness safety 
system. Used properly, this harness will keep your 
child seated  and safe. To secure your child in the 
harness, push  buckles (A) and (B) into the buckle 
housing (C) until  the buckle prongs snap into position. 
Carefully adjust slider (D) to fit snugly and comfortably 
around your child see (Fig 10).  Follow the same 
procedure to adjust the shoulder strap.  For infant use, 
we recommend using the extra buckle (E) for added 
security.  Always re-tighten the harness when your 
child is in a sit up or lay back position.

SAFETY HARNESS

CLOSING THE STROLLER FOR 
TRAVEL OR STORAGE

Each time, before closing your stroller, 
check the following:

a. Your child is clear of moving parts
b. The rear brakes have been set
c. The backrest is in the full upright  position
d. The front wheels are secure in the locked mode
e. The canopy is retracted
f. All items have been removed from the basket
g. The safety scarf is discharged

To close the stroller, push in on the main folding 
lock located in the middle of the stroller handle. 
With the main lock held in, pull up on the secondar y 
lock while easing the stroller handle down, (Fig 11). 
Check to be sure the red frame lock secures 
to the locking pin.  

LOCK

LOCK

PULL

PULL

Fig.11

PRESS

Tango SL808

IMPORTANT: READ THESE SAFETY INSTRUCTIONS CAREFULLY BEFORE USING 
YOUR STROLLER AND KEEP THEM FOR FUTURE REFERENCE. THE SAFETY OF 
YOUR CHILD DEPENDS ON IT.

Thank you for choosing Zooper. 

UNLOCKING & OPENING THE FRAME

To open the stroller, first lift up on the gray colored frame 
lock located on the left side of the stroller, (Fig 1). 
Be sure the frame lock detaches from the metal 
locking pin. Then pull up on the main stroller handle 
while pushing down on the top of the secondar y lock, 
(Fig 2). Using your hand, push down on the front edge 
of the seat to ensure the stroller frame has locked 
properly in the open position. Do not push down on the 
front armrest bar. 

    

  Be sure children are at a safe 

distance and cannot reach moving parts whenever 
opening or closing the stroller. 

Fig.2

Fig.1

The front wheels slide into the metal ends of each 
front leg tube. Press each wheel block firmly onto in
the metal end tubes until they "click" into position (Fig 3). 
Check  to see they have been properly installed by 
pulling down on the wheel block. 
It  should not move from the leg tube at  all. Should 
there be a need to remove the front wheels, first  
locate  the rounded metal spring lock on the side
of the metal wheel housing. Press the spring lock in 
while pulling the wheel off the front leg tube.

ATTACHING THE FRONT WHEELS TO 
THE FRAME

Fig.3

Fig.3

ATTACHING THE REAR AXLE & 
WHEELS TO THE FRAME

    

Do not use the stroller if the brake 

levers are not facing away from the stroller and if the 
locking pins are not visible as described above. 
Contact the appropriate service center listed at the 
back of these instructions if you have questions.

When engaging the brakes,only press on the brake
lever located on the inside of the wheels. Never
press down on the brake ber.
 

Fig.4

PRESS

PRESS

To lower the backrest, lift up on the plastic lever 
located in the middle of the seatback. While 
holding the lever up, move the seatback down 
into desired position and then release the lever 
(Fig 6). To raise the backrest, push up on the back 
of the seat until it  clicks  into the desired position.

    

Always keep your child in sight 

when making these kinds of adjustments. Check the 
fitting of the  safety harness each time the backrest 
is adjusted to be sure a  snug, yet comfortable 
fitting is maintained.

ADJUSTING THE SEATBACK

The rear wheels and rear axle come pre-assembled. 
Insert both plastic rear wheel housings onto the rear 
leg tubes of the stroller (Fig 4). Make sure the brake
levers are facing out, away from the stroller. Then 
push in each locking spring located on the rear 
stroller tubes. Holding the locking pin in, slide each 
wheel block over the pin until it locks into place and 
the silver head of the locking pin can be seen 
protruding from the wheel housing  (Fig  5).

Should there be a need to remove the rear wheel 
assembly, push in on the locking pins while pulling 
down on each wheel block.

Fig.6

Fig.5

To attach the front armrest to the stroller seat, line 
up the inserts of the armrest bar with the two plastic 
tabs on both sides of the stroller seat (Fig  7). 
Slide the  inserts completely into these slots, 
making sure that  both sides secure into a locked 
position. Pull out of each side of the armrest to make 
sure the  armrest is properly  locked  into the tabs. 
The armrest should not release  from the tabs. 
To remove the armrest, locate the plastic tabs 
underneath where the armrest connects to the 
sides of the stroller. Press in the tabs while pulling 
up out on the armrest.

 

ATTACHING THE ARMREST TO  
THE STROLLER SEAT

The safety scarf must be used whenever the seat is in 
a fully reclined position. The safety scarf is combined 
with 
footrest. When you use the scarf, adjust the footrest 
into the upright position. Then to line up the zipper of 
the footrest and the scarf and zip them 
together. (Fig  8).

USING THE SAFETY SCARF WHEN 
SEATBACK IS FULLY RECLINED

Your child may slip into leg 

openings and strangle. Never use the stroller with 
the backrest  fully reclined unless this baby safety 
scarf is  looped around the armrest  and secured 
in place.

IMPORTANT CARE AND SAFETY INFORMATION

Avoid serious injur y from falling or sliding out, always use safety harness provided.

Always engage the rear brakes when not holding onto your stroller.

Never leave your child unattended.

Never use the stroller near an open fire or exposed flame.

Never allow the stroller to be used as a toy.

Never allow more than one child at a time in the stroller, per seat. 

Never hang bags or other items from the handle or on the canopy. This may cause 

the stroller to become unstable.

Never use the stroller on stairs or escalators.

Do not overload the basket. Maximum load is 7 lbs. Excessive weight may cause a 

hazardous unstable condition to exist.

Do not overload the canopy pocket: Maximum load is 2 lbs. Excessive weight may 

create a hazardous unstable condition to exist. 

Before each use, check to make sure the stroller is set up properly and that all the 

wheels are properly and securely attached.

This stroller is not recommended for use with a child over 40lbs, excessive weight 

may damage the stroller and cause it to be unsafe.

This stroller is designed as a walking stroller. We do not recommend running, 

roller blading, or other such activities with this stroller.

The manufacturer does not approve use of any attachments designed to 

accommodate additional children, use of these types of attachments may cause 

your stroller to be unsafe and/or unstable and may void your warranty.

It may be unsafe to use accessories other than those approved by the manufacturer 

or distributor. 

Do not use if any part of the stroller becomes damaged, broken, unstable or missing. 

Discontinue use immediately and contact customer service. 

Failure to follow these warnings and instructions could result in serious injur y or death. 

Never use the product in a manner inconsistent with the manufacturers instructions. 

Do not fold your stroller when wet.
Machine wash removable seat and armrest covers using gentle cycle, 
cold water, and a mild detergent. The canopy can only be spot washed.
Line dr y fabric parts. 
Never use bleach when washing.
Do not leave your stroller in direct sunlight for extended periods of time.
Clean and lubricate all moving parts on the stroller frame and wheels 
as needed. Use only a penetrating silicon based lubricant.   
Regularly check for loose screws, broken parts, etc. Use only Zooper 
approved replacement parts available through the service centers listed below. 
Wipe off any sand, salt or other corrosive residue after each use where the stroller 
may be exposed to those elements. 

In order to maintain the highest quality standards, the distributor  reserves the 
right to improve or alter any Zooper stroller design without notice or obligation to 
any previous purchaser. For questions or service needs, please contact the 
service center located in your countr y of residence. Sending in your warrantee 
card will help expedite any service needs.

MAINTENANCE

Never pick up your stroller by the 

armrest.To avoid serious injur y, ensure that children's 
hands, arms, and feet are well clear of the bumper 
bar before opening or closing it.

CAR SEAT COMPATIBILITY 

Although we have done our best to make the Zooper 
Tango as universally compatible as possible, the infant 
seat you have chosen may not fit well in the stroller. The 
models that we have tested and approved are:
Evenflo On My Way
Graco Snug Ride and Safe Seat
Britax Companion

To install an infant carrier, first be sure that the infant 
carrier is not attached to its permanent car base. Locate 
the car seat adapter strap that was packaged with your 
stroller. It should have a buckle in the center, and a clip 
on each end. Next, identify the D-rings located in the hip 
points of the stroller seat. Ensure that infant seat has 
been removed from its permanent car base.

rd

th

Step 1  Recline the stroller seat to the 3  or 4  position. 
Step 2  Attach the car seat adapter strap to the stroller
            Seat by clipping the ends to  the D-rings. Adjust
            the strap  so that it is fully extended. Unbuckle the
            center, and  lay the ends out over the armrests of 
            the troller  seat.          
             
Step 3  Place the infant seat into the stroller seat, so that 
             the infant seat is facing the  parent. Depending
             On  the size and design of your seat, you will 
             Either  place it  inside the bumper bar, or over the
             Bumper  bar.                  
             
Step 4  Bring the ends of the adapter strap back over the
             infant seat, and buckle the center. The belt
             Should  be positioned so that it travels over the
             lap of the  infant seat. Some models have belt
             guides located  on the sides, if your model  does;
             make sure the  strap is positioned inside these
             guides.
Step 5  Tighten the strap down so that infant seat is 
             securely fixed into the stroller  seat. Infant seat
             should not lift out of the stroller seat if properly
             strapped in.

Fig.7

Fig.8

Fig.9

Shoulders

Straps

A

B

C

D

Fig.10

E