Munchkin CCD-0113-001 REV1 プリント
Instructions for use: Wash and inspect before use.
Top rack dishwasher safe. Safe for boiling and steam
sterilizing. Safe for all ages.
Top rack dishwasher safe. Safe for boiling and steam
sterilizing. Safe for all ages.
Sterilizing: Before first use, disassemble the bottle
and place all bottle parts in boiling water for
5 minutes or use the Munchkin
and place all bottle parts in boiling water for
5 minutes or use the Munchkin
®
SteamGuard™
Microwave or Electric Sterilizer for proper hygiene.
Cleaning and Maintenance: Carefully disassemble
the bottle. To remove the valve from the bottom of
the bottle, grasp any portion of the circular
flange/disc and pull outward until loose. Wash and
rinse each piece separately and thoroughly. Carefully
clean valve to avoid tearing. Sterilize using a sterilizer
or boil for 5 minutes. All components are top rack
dishwasher safe. Use dishwasher basket to secure
components during wash and dry cycles.
the bottle. To remove the valve from the bottom of
the bottle, grasp any portion of the circular
flange/disc and pull outward until loose. Wash and
rinse each piece separately and thoroughly. Carefully
clean valve to avoid tearing. Sterilize using a sterilizer
or boil for 5 minutes. All components are top rack
dishwasher safe. Use dishwasher basket to secure
components during wash and dry cycles.
Assembly: Before each use, hold
the tip of the valve (triangular
head) up to the light to see the
slit and pinch apart to ensure
proper venting. When assembling
your LATCH bottle, first push the
valve firmly through the hole at
the bottom of the bottle. Make
sure that the triangular head of the valve is fully inserted.
A fully inserted valve will have a visible gap between the
bottom edge of the triangular head against the hole
opening at the bottom of the bottle. You may not always
see a gap unless you apply upward pressure with your
thumb, as you inspect. (see Figure 1)
the tip of the valve (triangular
head) up to the light to see the
slit and pinch apart to ensure
proper venting. When assembling
your LATCH bottle, first push the
valve firmly through the hole at
the bottom of the bottle. Make
sure that the triangular head of the valve is fully inserted.
A fully inserted valve will have a visible gap between the
bottom edge of the triangular head against the hole
opening at the bottom of the bottle. You may not always
see a gap unless you apply upward pressure with your
thumb, as you inspect. (see Figure 1)
Next, pull the nipple through the collar, ensuring that the
flanges are tucked underneath. It is easier to assemble if you
pull the nipple back and forth upwards, instead of pulling it
up straight. Make sure the 3rd segment under the accordion
is resting above the collar. The area where the nipple and
collar meet should be flush (no gap). (see Figure 2)
flanges are tucked underneath. It is easier to assemble if you
pull the nipple back and forth upwards, instead of pulling it
up straight. Make sure the 3rd segment under the accordion
is resting above the collar. The area where the nipple and
collar meet should be flush (no gap). (see Figure 2)
Screw the collar onto the thread of the bottle in a
clockwise direction to securely tighten the collar. When
assembling the cap, make sure to place the cap vertically
onto the bottle so the nipple sits upright and is sealed.
clockwise direction to securely tighten the collar. When
assembling the cap, make sure to place the cap vertically
onto the bottle so the nipple sits upright and is sealed.
Compatibility: Only use Munchkin LATCH nipples
with Munchkin LATCH bottles. Replacement nipples
are available separately. Make sure that you are
feeding your baby
with the correct flow
rate nipple.
with Munchkin LATCH bottles. Replacement nipples
are available separately. Make sure that you are
feeding your baby
with the correct flow
rate nipple.
WARNING:
Do not let child take a
bottle to bed or self-feed for long periods. Continuous and
prolonged sucking of fluids will cause tooth decay. To prevent
possible choking hazard, test strength of nipple by pulling on
bulb portion. Discontinue if any tear or crack appears on
nipple. Do not allow child to use the nipple as a teether. Always
test temperature of liquid before feeding baby. Do not warm
contents in a microwave oven. Do not let child walk or run
while carrying bottle. Do not leave child unattended. This is not
a toy. Keep all components not in use out of the reach of
children. Discard and replace at first sign of weakness or
damage. Discard all packaging components before use.
prolonged sucking of fluids will cause tooth decay. To prevent
possible choking hazard, test strength of nipple by pulling on
bulb portion. Discontinue if any tear or crack appears on
nipple. Do not allow child to use the nipple as a teether. Always
test temperature of liquid before feeding baby. Do not warm
contents in a microwave oven. Do not let child walk or run
while carrying bottle. Do not leave child unattended. This is not
a toy. Keep all components not in use out of the reach of
children. Discard and replace at first sign of weakness or
damage. Discard all packaging components before use.
PRODUCT AND DESIGN ARE TM & ©2013 MUNCHKIN, INC.
MUNCHKIN, THE LATCH LOGO, AND IT’S THE LITTLE
THINGS ARE TRADEMARKS OR REGISTERED TRADEMARKS
OF MUNCHKIN, INC. 7835 GLORIA AVE., VAN NUYS, CA
91406. PATENT: HTTP://WWW.MUNCHKIN.COM/PATENTS.
MADE IN CHINA/FABRIQUÉ EN CHINE.
CCD-0113-001 REV1
instructions
4oz / 118ml
8oz / 237ml
bottles
8oz / 237ml
bottles
Nipple
Collar
Bottle
Sealing Disc
Valve
Cap
0m+
3m+
6m+
Figure 1
Visible gap
with valve
inserted
with valve
inserted
Figure 2
FRONT
BACK