InSinkErator 14481 ユーザーズマニュアル
12
PROPERTY DAMAGE
System.has.hot.water.spray.that.must.be..
connected..Fresh.water.connection.to.the..
Waste.Xpress.must.be.hot.water.only..Failure..
to.use.hot.water.may.clog.system.and.result..
in.malfunction.
connected..Fresh.water.connection.to.the..
Waste.Xpress.must.be.hot.water.only..Failure..
to.use.hot.water.may.clog.system.and.result..
in.malfunction.
WASTE OUTLET LINE
Connect.a.2".drain.line.to.the.Waste.Xpress.waste..
outlet.as.specified.per.local.codes.(see.Figure.18..
for.water.outlet.location).
outlet.as.specified.per.local.codes.(see.Figure.18..
for.water.outlet.location).
InSinkErator.recommends.that.the.water.outlet..
empties.into.a.floor.drain.
empties.into.a.floor.drain.
If.the.water.outlet.connection.on.the.Waste.Xpress
needs.to.be.switched.to.the.other.side,.complete..
the.following:
needs.to.be.switched.to.the.other.side,.complete..
the.following:
•.Remove.the.four.screws.holding.the.cap.and.gasket.in.
position.(see.Figure.18).
•.Install.gasket,.cap.and.inlet.fitting.on.reverse.side..
and.secure.with.appropriate.screws.
NOTE: The Waste Xpress system should not be
plumbed directly into a small inside grease trap.
The unit can be plumbed through a large exterior
grease trap.
plumbed directly into a small inside grease trap.
The unit can be plumbed through a large exterior
grease trap.
WATER SUPPLY CONNECTIONS
When.connecting.the.incoming.water.supply.to.the
disposer,.sink.bowl.and.Waste.Xpress,.use.as.few
elbows.and.tees.as.possible.
disposer,.sink.bowl.and.Waste.Xpress,.use.as.few
elbows.and.tees.as.possible.
All.cold.water.line.fittings.are.1/2".NPT.except.the
sink.bowl.nozzles.which.are.1/2".compression...
Use.1/2".compression.fitting.to.connect.hot.water..
to.Waste.Xpress.
sink.bowl.nozzles.which.are.1/2".compression...
Use.1/2".compression.fitting.to.connect.hot.water..
to.Waste.Xpress.
Install.the.flow.control.valve,.water.solenoid.valve,
and.syphon.breaker.according.to.the.direction.of.the
arrows.marked.on.each.valve.body.
and.syphon.breaker.according.to.the.direction.of.the
arrows.marked.on.each.valve.body.
NOTE: In-line hot and cold shutoff valves are
recommended close to the Waste Xpress system
for ease of service.
recommended close to the Waste Xpress system
for ease of service.
ROUTING WATER FLOW
Connect.cold.water.only.to.disposer,.bowl,.or.trough.
Connect.hot.water.only.to.Waste.Xpress.for.hot.water
spray.nozzles.
spray.nozzles.
In.a.trough.system,.route.all.water.flow.to.the.end.of
the.trough.to.flush.food.waste.
the.trough.to.flush.food.waste.
Figure 19. Typical Installation Diagram
PLUMBING CONNECTIONS
The.syphon.breaker.is.supplied.with.all.Waste.Xpress.
systems.(packed.separately).
systems.(packed.separately).
Syphon.breaker.must.be.installed.above.the.sink.flood
plane.
plane.
per local plumbing codes..Check.direction.of.
water.flow.arrows.
The.solenoid.valve.is.supplied.with.a.24.V.coil.
•.The.flow.control.valve.regulates.all.cold.water.flowing
. into.the.disposer.and.Waste.Xpress..This.conserves..
. water.and.prevents.overloading.
. into.the.disposer.and.Waste.Xpress..This.conserves..
. water.and.prevents.overloading.
Plumbing Connections
Flow Control Valve
Disposer
Sink Bowl
Syphon Breaker
Cold Water Solenoid
Hot Water Solenoid
Waste Xpress
Shut Off Valve
(supplied
by others)
WX-101A Controller
10 max
(3.1 m max)
1-1/2" min
(38.1 mm
min)
1" min
(25.4 mm min)