Samsung 120GB PATA HDD HS122JB プリント
製品コード
HS122JB
Ultra mobile PATA/ZIF
Spinpoint N2
30GB
40GB
60GB
80GB
100GB
120GB
160GB
3600 RPM class
2MB Buffer
HS031GA
HS041HA
HS061HA
HS080HA
4200 RPM class
2MB Buffer
HS030GB
HS040HB
HS060HB
HS080HB
HS120JB
HS160JB
8MB Buffer
HS04THB
HS06THB
HS082HB
HS10TJB
HS122JB
FEATURES
• MAX.80GB Formatted Capacity Per Disk
• ATA S.M.A.R.T Compliant
• High Speed Digital Signal Processor Based Architecture
• ATA 28-bit Address Feature Set
• Low Power HDC
• Multi-Burst On-The-Fly Error Correction
• Advanced Power Management Control
• SilentSeek™
• Fluid Dynamic Bearing Spindle Motor Technology
• Free Fall Sensor (optional)
Capacity
30 / 40 / 60 / 80 / 100 / 120 / 160GB
Temperature
Interface
PATA/ZIF
Operating
5 ~ 60 ℃
Rotational Speed
3600 / 4200 RPM class
Non-operating
-40 ~ 85 ℃
Buffer DRAM Size
2 / 8 MB
Humidity (non-condensing)
Byte per Sector
512
Operating
8 ~ 90 ％
Non-operating
8 ~ 90 ％
PERFORMANCE SPECIFICATION
Linear Shock (1/2 sine pulse)
Average Seek time (typical)
15.0 ms
Operating, 2ms
600 G
Average Latency
8.3 ms
Non-operating, 1ms
1500 G
Media Transfer Rate (Max.)
Vibration
3600RPM class
410 Mb/s
Operating
0.67 Grms
4200RPM class
458 Mb/s
Altitude (relative to sea level)
Interface Transfer Rate (Max.)
100 MB/s
Operating
-300 to 3.000 m
Drive Ready Time (typical)
2.0 sec
Non-operating
-400 to 15,000 m
RELIABILITY SPECIFICATION
PHYSICAL DIMENSION
Non-recoverable Read Error
1 sector in 10^13 bits
Height
Controlled Ramp Load/Unload
600,000
30/40/60/80GB
5.0 mm
100/120/160GB
8.0 mm
ACOUSTICS
Width
71.0 mm
Idle
Length
54.0 mm
30/40/60/80GB
1.6 Bel
Weight (Max.)
100/120/160GB
1.8 Bel
30/40/60/80GB
48 g
Performance Seek
100/120/160GB
59 g
30/40/60/80GB
2.2 Bel
100/120/160GB
2.4 Bel
POWER REQUIREMENTS
Voltage
+3.3V ±5%
Spin-up Current (Max.)
400 mA
Seek (typical)
0.8 W
Read/Write (typical)
* Note : Design and specifications are subject to change without prior notice.
30/40/60/80GB
0.9 W
1MB = 1,000,000 Bytes, 1GB = 1,000,000,000 Bytes
100/120/160GB
1.0 W
* Accessible capacity may vary as some OS uses binary numbering system for
Idle (typical)
0.30 W
reported capacity.
Standby (typical)
0.07 W
* A small portion of the (2/8MB) buffer memory is reserved for firmware use.
Sleep (typical)
0.07 W
* 160GB 48-bit Address Feature Set
1.8" HDD product specification Rev.07
Match with product manual Rev 02
Capacity
DRIVE CONFIGURATION
ENVIRONMENTAL SPECIFICATIONS