Gigaset A400A ユーザーズマニュアル
14
A400/A400A / GBR / A31008-M2201-L101-1-7619 / main.fm / 29.06.2010
Specifications
Recommended batteries
Only use rechargeable batteries as described below.
Technology: Nickel-metal-hydride
Technology: Nickel-metal-hydride
(NiMH)
Size:
AAA (Micro, HR03)
Voltage:
1.2 V
Capacity:
400–800 mAh
The device is supplied with two approved batteries.
Base power consumption
General specifications
Questions and answers
If you have any queries about the use of your tele-
phone, visit our website at
phone, visit our website at
www.gigaset.com/service
for assistance 24/7. The table below contains a list of
common problems and possible solutions.
common problems and possible solutions.
In standby mode
- Charged handset in base
- Charged handset in base
- Handset not in base
approx. 0.7 W
< 0.4 W
< 0.4 W
During a call
approx. 0.5 W
DECT standard
Is supported
GAP standard
Is supported
(The Gigaset handset is only fully
functional on Gigaset bases)
functional on Gigaset bases)
Range
Up to 300 m outdoors
Up to 50 m indoors
Base power supply
230 V ~/50 Hz
Environmental condi-
tions in operation
tions in operation
+5°C to +45°C, 20% to 75% relative
humidity
humidity
Standby time
220 hours
Talktime
20 hours
Operating time for 1.5
hours of calls per day
hours of calls per day
- Without Eco Mode+
- With Eco Mode+
135 hours
90 hours
90 hours
Charging time in
charger
charger
5.5 hours
Problem
Cause
Solution
Nothing
appears in the
display.
appears in the
display.
The handset is not
switched on.
switched on.
The batteries are
flat.
flat.
Press the end call key
a
for approx.
5 seconds or place the
handset in the base.
Charge or replace the
batteries.
handset in the base.
Charge or replace the
batteries.
No wireless
connection to
the base, Base
flashes in the
display.
connection to
the base, Base
flashes in the
display.
The handset is out-
side the range of
the base.
The handset is not
registered.
The base is not
switched on.
side the range of
the base.
The handset is not
registered.
The base is not
switched on.
Move the handset
closer to the base.
closer to the base.
Register the handset
Check the mains con-
nector on the base
nector on the base
You cannot
hear a ringer
melody/dial-
ling tone from
the fixed line
network.
hear a ringer
melody/dial-
ling tone from
the fixed line
network.
The phone cord
supplied has not
been used or has
been replaced by a
new cord with the
wrong pin connec-
tions.
supplied has not
been used or has
been replaced by a
new cord with the
wrong pin connec-
tions.
Please always use the
phone cord supplied or
ensure that the pin
connections are cor-
rect when purchasing
from a retailer: 3-4
assignment of tele-
phone leads/EURO
CTR37.
phone cord supplied or
ensure that the pin
connections are cor-
rect when purchasing
from a retailer: 3-4
assignment of tele-
phone leads/EURO
CTR37.
Error tone
sounds after
sounds after
system PIN
prompt.
prompt.
PIN forgotten.
You have entered
the wrong system
PIN.
the wrong system
PIN.
All handsets are de-
registered. All settings
are reset. All lists are
deleted.
registered. All settings
are reset. All lists are
deleted.
The connec-
tion always
terminates
after approx.
30 seconds.
tion always
terminates
after approx.
30 seconds.
Repeater acti-
vated/deactivated
vated/deactivated
Deactivate and
reactivate the handset
reactivate the handset