Maytag mer5605w ユーザーガイド
5
COOKTOP USE
The control knobs can be set to anywhere between HI and LO.
Push in and turn to setting.
Push in and turn to setting.
Cooktop On Indicator Light (on some models)
The Cooktop On indicator light is located on the console panel.
When any control knob on the console panel is turned on, the
Cooktop On indicator light will glow.
When any control knob on the console panel is turned on, the
Cooktop On indicator light will glow.
Coil Elements and Burner Bowls (on some models)
Coil elements should be level for optimal cooking results. Burner
bowls, when clean, reflect heat back to the cookware. They also
help catch spills.
Cookware should not extend more than ½" (1.3 cm) over the coil
element. If cookware is uneven or too large, it can produce excess
heat, causing the burner bowl to change color.
bowls, when clean, reflect heat back to the cookware. They also
help catch spills.
Cookware should not extend more than ½" (1.3 cm) over the coil
element. If cookware is uneven or too large, it can produce excess
heat, causing the burner bowl to change color.
OVEN USE
Odors and smoke are normal when the oven is used the first few
times, or when it is heavily soiled.
times, or when it is heavily soiled.
IMPORTANT: The health of some birds is extremely sensitive to the
fumes given off. Exposure to the fumes may result in death to
certain birds. Always move birds to another closed and well-
ventilated room.
fumes given off. Exposure to the fumes may result in death to
certain birds. Always move birds to another closed and well-
ventilated room.
Electronic Oven Controls
Control Display
The display will flash when powered up or after a power loss. Press
CANCEL to clear. When oven is not in use, the time of day is
displayed. Indicator lights show functions that are in use.
CANCEL to clear. When oven is not in use, the time of day is
displayed. Indicator lights show functions that are in use.
Tones
Tones are audible signals, indicating the following:
Basic Functions
One tone
■
Valid pad press
■
Oven is preheated (long tone)
■
Function has been entered
■
Reminder (on some models), repeating each minute after the
end-of-cycle tones
end-of-cycle tones
Three tones
■
Invalid pad press
Four tones
■
End of cycle
Fahrenheit and Celsius
The temperature is preset at Fahrenheit, but can be changed to
Celsius.
To change: Press and hold BROIL for 5 seconds. A tone will
sound, and “°C” or “°F” will appear on the display. Repeat to
change back.
To exit mode, press CANCEL.
Celsius.
To change: Press and hold BROIL for 5 seconds. A tone will
sound, and “°C” or “°F” will appear on the display. Repeat to
change back.
To exit mode, press CANCEL.
BROIL
Broiling
1. Position cookware in oven and close door to broil stop position. The door should remain open
approximately 5" (12.7 cm).
2. Press BROIL.
3. Press TEMP/TIME “+” or “-” arrow pads to change the temperature in 5°F (5°C) increments
3. Press TEMP/TIME “+” or “-” arrow pads to change the temperature in 5°F (5°C) increments
between 300°F and 525°F (150°C and 275°C).
4. Press START.
5. Press CANCEL when finished.
5. Press CANCEL when finished.
START
Cooking start
The Start pad begins any oven function. If Start is not pressed within 5 seconds, “PSH” appears in
the display. If Start is not pressed within 1 minute after pressing a keypad, the function is canceled
and the time of day is displayed.
the display. If Start is not pressed within 1 minute after pressing a keypad, the function is canceled
and the time of day is displayed.
CANCEL
Range function
The Cancel keypad stops any function except the Clock, Kitchen Timer, and Oven Control
Lockout.
Lockout.
TEMP/TIME
Temperature and
time adjust
time adjust
The “+” or “-” arrow pads are used to adjust time and temperature settings.
KEYPAD
FEATURE
INSTRUCTIONS
WARNING
Fire Hazard
Turn off all controls when done cooking.
Failure to do so can result in death or fire.
REMEMBER: When range is in use or (on some models)
during the Self-Cleaning cycle, the entire cooktop area may
become hot.
during the Self-Cleaning cycle, the entire cooktop area may
become hot.