Alcatel-Lucent 6850-48 ネットワークガイド
Configuring Ethernet Ports
Setting Ethernet Combo Port Parameters
OmniSwitch AOS Release 6 Network Configuration Guide
September 2009
page 1-25
To configure the duplex mode on a single combo port, enter interfaces, followed by the slot number, a
slash (/), the combo port number, hybrid, either fiber or copper, duplex, and the desired duplex setting
(auto, full, or half). For example, to set the duplex mode on the fiber combo port 23 on slot 2 to full,
enter:
slash (/), the combo port number, hybrid, either fiber or copper, duplex, and the desired duplex setting
(auto, full, or half). For example, to set the duplex mode on the fiber combo port 23 on slot 2 to full,
enter:
-> interfaces 2/23 hybrid fiber duplex full
To configure the duplex mode on a range of combo ports, enter interfaces, followed by the slot number, a
slash (/), the first combo port number, a hyphen (-), the last combo port number, hybrid, either fiber or
copper, duplex, and the desired duplex setting (auto, full, or half). For example, to set the duplex mode
on fiber combo ports 21 through 24 on slot 2 to full, enter:
slash (/), the first combo port number, a hyphen (-), the last combo port number, hybrid, either fiber or
copper, duplex, and the desired duplex setting (auto, full, or half). For example, to set the duplex mode
on fiber combo ports 21 through 24 on slot 2 to full, enter:
-> interfaces 2/21-24 hybrid fiber duplex full
Configuring Autonegotiation and Crossover for Combo Ports
The following subsections describe how to enable and disable autonegotiation (see
) and configure crossover settings (see
) on combo ports.
Enabling and Disabling Autonegotiation for Combo Ports
By default, autonegotiation is enabled. To enable or disable autonegotiation on a single combo port, a
range of combo ports, or all combo ports on an entire switch (slot), use the
range of combo ports, or all combo ports on an entire switch (slot), use the
for more information).
Note. In the interfaces hybrid autoneg command, the copper keyword is used to configure the copper
RJ-45 10/100/1000 port while the fiber keyword is used to configure the fiber SFP connector.
RJ-45 10/100/1000 port while the fiber keyword is used to configure the fiber SFP connector.
To enable or disable autonegotiation on all combo ports in an entire switch, enter interfaces, followed by
the slot number, hybrid, either fiber or copper, autoneg, and either enable or disable. For example, to
enable autonegotiation on all copper combo ports on slot 2, enter:
the slot number, hybrid, either fiber or copper, autoneg, and either enable or disable. For example, to
enable autonegotiation on all copper combo ports on slot 2, enter:
-> interfaces 2 hybrid copper autoneg enable
Note. using the interface hybrid autoneg command to set all combo ports on a switch will not affect the
configurations of the non-combo ports.
configurations of the non-combo ports.
To enable or disable autonegotiation on a single combo port, enter interfaces, followed by the slot
number, a slash (/), the combo port number, hybrid, either fiber or copper, autoneg, and either enable or
disable. For example, to enable autonegotiation on copper combo port 23 on slot 2, enter:
number, a slash (/), the combo port number, hybrid, either fiber or copper, autoneg, and either enable or
disable. For example, to enable autonegotiation on copper combo port 23 on slot 2, enter:
-> interfaces 2/23 hybrid copper autoneg enable
To enable or disable autonegotiation on a range of combo ports, enter interfaces, followed by the slot
number, a slash (/), the first combo port number, a hyphen (-), the last combo port number, hybrid, either
fiber or copper, autoneg, and either enable or disable. For example, to enable autonegotiation on copper
combo ports 21 through 24 on slot 2, enter:
number, a slash (/), the first combo port number, a hyphen (-), the last combo port number, hybrid, either
fiber or copper, autoneg, and either enable or disable. For example, to enable autonegotiation on copper
combo ports 21 through 24 on slot 2, enter:
-> interfaces 2/21-24 hybrid copper autoneg enable