Alcatel-Lucent 6850-48 参照ガイド
PIM Commands
OmniSwitch CLI Reference Guide
September 2009
page 45-89
ipv6 pim interface
Enables IPv6 PIM and configures the statistics such as hello-interval, triggered-hello, hello-holdtime, join-
prune, prune-delay, override-interval, dr-priority, stub interface, prune limit interval, and graft retry inter-
val on the IPv6 interface.
prune, prune-delay, override-interval, dr-priority, stub interface, prune limit interval, and graft retry inter-
val on the IPv6 interface.
ipv6 pim interface if_name [hello-interval seconds] [triggered-hello seconds] [joinprune-interval
seconds] [hello-holdtime seconds] [joinprune-holdtime seconds] [prune-delay milliseconds] [override-
interval milliseconds] [dr-priority priority] [[no] stub] [prune-limit-interval seconds] [graft-retry-
interval seconds]
seconds] [hello-holdtime seconds] [joinprune-holdtime seconds] [prune-delay milliseconds] [override-
interval milliseconds] [dr-priority priority] [[no] stub] [prune-limit-interval seconds] [graft-retry-
interval seconds]
no ipv6 pim interface if_name
Syntax Definitions
if_name
The interface name on which the IPv6 PIM is being enabled or disabled.
hello-interval seconds
The frequency at which IPv6 PIM Hello messages are transmitted on
this interface, in seconds. Values may range from 0 to 18000.
this interface, in seconds. Values may range from 0 to 18000.
triggered-hello seconds
Specifies the maximum time, in seconds, before a triggered IPv6 PIM
Hello message is sent on this interface. Values may range from 0 to 60.
Hello message is sent on this interface. Values may range from 0 to 60.
joinprune-interval seconds
The frequency at which periodic IPv6 PIM Join/Prune messages are sent
on this interface, in seconds. Values may range from 0 to 18000.
on this interface, in seconds. Values may range from 0 to 18000.
hello-holdtime seconds
Specifies the value of the IPv6 PIM hello-holdtime for this interface.
This value is set in the Holdtime field of IPv6 PIM Hello messages sent
on this interface, in seconds. Values may range from 0 to 65535.
This value is set in the Holdtime field of IPv6 PIM Hello messages sent
on this interface, in seconds. Values may range from 0 to 65535.
joinprune-holdtime seconds
Specifies the value that is set in the Holdtime field of the IPv6 PIM
Joinprune messages sent on this interface, in seconds.Values may range
from 0 to 65535.
Joinprune messages sent on this interface, in seconds.Values may range
from 0 to 65535.
prune-delay milliseconds
Specifies the value of the expected propagation delay between IPv6
PIM routers on this network, inserted into the LAN prune-delay option
of the IPv6 PIM Hello messages sent on this interface, in milliseconds.
Values may range from 0 to 32767.
PIM routers on this network, inserted into the LAN prune-delay option
of the IPv6 PIM Hello messages sent on this interface, in milliseconds.
Values may range from 0 to 32767.
override-interval milliseconds
Specifies the value set in the Override Interval field of the LAN prune-
delay option of the IPv6 PIM Hello messages sent on this interface, if
the prune-delay status is enabled, in milliseconds. Values may range
from 0 to 65535.
delay option of the IPv6 PIM Hello messages sent on this interface, if
the prune-delay status is enabled, in milliseconds. Values may range
from 0 to 65535.
dr-priority priority
Specifies the Designated Router priority set in the DR priority option on
this interface. The DR priority option value (1–192). A higher numeric
value denotes a higher priority.
this interface. The DR priority option value (1–192). A higher numeric
value denotes a higher priority.
prune-limit-interval seconds
Specifies the minimum interval that must elapse between two succes-
sive IPv6 PIM prune messages sent on this interface, in seconds. Values
may range from 0 to 65535.
sive IPv6 PIM prune messages sent on this interface, in seconds. Values
may range from 0 to 65535.
graft-retry-interval seconds
Specifies the minimum interval that must elapse between two succes-
sive IPv6 PIM graft messages sent on this interface, in seconds. Values
may range from 0 to 65535.
sive IPv6 PIM graft messages sent on this interface, in seconds. Values
may range from 0 to 65535.