Genz-Benz 6025 ユーザーガイド
FEATURES
12AX7A TUBE DRIVER®
Preamp 25 Watt MosValve™ Amplifier section
Classic Voiced 10” speaker
3 band EQ section
Accutronics® Reverb
Headphone Jack
Dual Voltage switch
OPERATION
The 6025 has been designed as a unique high quality practice amp with enough
power and tone for small performance venues. The tube preamp section and the 25
watt MosValve™ amp section combine to provide anything from a smooth, warm
"clean" sound, all the way to a huge “super-overdrive” crunch.
TUBE DRIVE—This control provides the pre-gain to the 12AX7A tube. Use this control
with the Master control to dial in all desired sounds. For a good clean sound this con-
trol should be set at the 3 or 4 position. As this control is increased, tube over-drive
increases. NOTE: At the 8 to 10 position the tube is driven into a @Super-Overdrive"
stage for extreme distortion.
MASTER—This control provides the Master volume fo r the Preamp stage. Use this
control in conjunction with the Tube Drive control for sounds from “Clean” to “Super
Over-Drive".
EQUALIZATION—3 bands of passive EQ are provided for tone shaping.
REVERB—This control sets the amount of signal sent to the Accutronics® Reverb
unit. Increased Tube Drive level will increase the Reverb level.
HEADPHONE JACK—Use this output for your headphones when silent practicing is
desired. The 10" speaker is turned off when headphones are inserted.
POWER INLET RECEPTACLE—The 6025 features a dual voltage transformer for ei-
ther 115V or 230V operation. IN THE USA, ALWAYS USE THE 3 PRONG DETACH-
ABLE CORD SUPPLIED, AND THE VOLTAGE SWITCH MUST BE IN THE 115V PO-
SITION.
EXPOSURE—Common sense (as well as the law) dictates that you do not operate the
unit where it will be exposed to moisture or rain, excessive ambient heat (over 110 de-
grees F / 40 degrees C) or without a properly grounded A.C. power connector.
power and tone for small performance venues. The tube preamp section and the 25
watt MosValve™ amp section combine to provide anything from a smooth, warm
"clean" sound, all the way to a huge “super-overdrive” crunch.
TUBE DRIVE—This control provides the pre-gain to the 12AX7A tube. Use this control
with the Master control to dial in all desired sounds. For a good clean sound this con-
trol should be set at the 3 or 4 position. As this control is increased, tube over-drive
increases. NOTE: At the 8 to 10 position the tube is driven into a @Super-Overdrive"
stage for extreme distortion.
MASTER—This control provides the Master volume fo r the Preamp stage. Use this
control in conjunction with the Tube Drive control for sounds from “Clean” to “Super
Over-Drive".
EQUALIZATION—3 bands of passive EQ are provided for tone shaping.
REVERB—This control sets the amount of signal sent to the Accutronics® Reverb
unit. Increased Tube Drive level will increase the Reverb level.
HEADPHONE JACK—Use this output for your headphones when silent practicing is
desired. The 10" speaker is turned off when headphones are inserted.
POWER INLET RECEPTACLE—The 6025 features a dual voltage transformer for ei-
ther 115V or 230V operation. IN THE USA, ALWAYS USE THE 3 PRONG DETACH-
ABLE CORD SUPPLIED, AND THE VOLTAGE SWITCH MUST BE IN THE 115V PO-
SITION.
EXPOSURE—Common sense (as well as the law) dictates that you do not operate the
unit where it will be exposed to moisture or rain, excessive ambient heat (over 110 de-
grees F / 40 degrees C) or without a properly grounded A.C. power connector.
a division of Genz Benz Enclosures
7811 E. Pierce St. Scottsdale, AZ 85257
602-941-0705 FAX 602-946-2412