Genz-Benz 6150 ユーザーガイド
MASTER VOLUME – Adjusts the post-effects overall volume of the amplifier before the power amp. It
functions pretty much as you would expect!
POWER SWITCH – Turns the AC mains power on and off, indicated by green LED above switch.
EFFECTS SEND/RECEIVE JACKS – The ¼” send jack provides a nominal –10dB output signal to drive
any common effects processor with “wet/dry mix control”. This jack is configured as an “insert” jack and
interrupts the signal between the preamp and the power amp. The send jack can also be used as an un-
balanced line level output. The ¼” return jack is used to return the processed signal back into the ampli-
fier. This jack contains a switch that automatically opens the return jack signal loop when processing is
used. The “mix” control on the effects device is now used to set the balance between the
“wet” (processed only) and the “dry” (unprocessed) signals.
HEADPHONE OUTPUT– Used to connect standard headphones (8 – 600 ohm). A speaker switch on the
back panel shuts off the speaker on all models, allowing private practice or studio work with a minimum of
fuss and bother, not to mention noise! This output is short circuit protected.
XLR BALANCED DIRECT OUTPUT– This frequency compensated output is used to connect the ampli-
fier to any standard balanced PA system mixer input. The level is nominal –30dBv (hot mic level) for
maximum flexibility. The ground lift switch opens pin 1 to eliminate ground loops between the amplifier
and the PA system. Select the position with minimum hum. This output is protected against phantom
power present on the mic input from the mixer console.
POWER AMPLIFIER – The 6100 series uses an integrated power operational amplifier to drive the load.
This fully monolithic design features complete short circuit and thermal protection built right into the sili-
con die for high reliability under adverse conditions.
SPEAKER AND CABINET – The 6100 family uses Celestion
functions pretty much as you would expect!
POWER SWITCH – Turns the AC mains power on and off, indicated by green LED above switch.
EFFECTS SEND/RECEIVE JACKS – The ¼” send jack provides a nominal –10dB output signal to drive
any common effects processor with “wet/dry mix control”. This jack is configured as an “insert” jack and
interrupts the signal between the preamp and the power amp. The send jack can also be used as an un-
balanced line level output. The ¼” return jack is used to return the processed signal back into the ampli-
fier. This jack contains a switch that automatically opens the return jack signal loop when processing is
used. The “mix” control on the effects device is now used to set the balance between the
“wet” (processed only) and the “dry” (unprocessed) signals.
HEADPHONE OUTPUT– Used to connect standard headphones (8 – 600 ohm). A speaker switch on the
back panel shuts off the speaker on all models, allowing private practice or studio work with a minimum of
fuss and bother, not to mention noise! This output is short circuit protected.
XLR BALANCED DIRECT OUTPUT– This frequency compensated output is used to connect the ampli-
fier to any standard balanced PA system mixer input. The level is nominal –30dBv (hot mic level) for
maximum flexibility. The ground lift switch opens pin 1 to eliminate ground loops between the amplifier
and the PA system. Select the position with minimum hum. This output is protected against phantom
power present on the mic input from the mixer console.
POWER AMPLIFIER – The 6100 series uses an integrated power operational amplifier to drive the load.
This fully monolithic design features complete short circuit and thermal protection built right into the sili-
con die for high reliability under adverse conditions.
SPEAKER AND CABINET – The 6100 family uses Celestion
ä speakers, perfectly matched to the
closed back style cabinets. A bottom mounted tilt-back handle is provided so the amp can point up to-
wards the performer. Finished in a textured vinyl finish, the cabinet sports a clean, no nonsense look that
shows that it is a serious music-making machine.
POWER INLET – A removable IEC style power inlet cordset is used to connect the AC mains power to
the amplifier. Various voltages and cordsets are available, depending on the destination country. An inter-
nal (non-user replaceable) protection fuse is provided on the main circuit board. The Mains (line) voltage
is nominal 115 volts or 230 volts AC (depending on destination country), +/- 10%. The amplifier will oper-
ate on either 50 or 60 Hz.
WARRANTY:
wards the performer. Finished in a textured vinyl finish, the cabinet sports a clean, no nonsense look that
shows that it is a serious music-making machine.
POWER INLET – A removable IEC style power inlet cordset is used to connect the AC mains power to
the amplifier. Various voltages and cordsets are available, depending on the destination country. An inter-
nal (non-user replaceable) protection fuse is provided on the main circuit board. The Mains (line) voltage
is nominal 115 volts or 230 volts AC (depending on destination country), +/- 10%. The amplifier will oper-
ate on either 50 or 60 Hz.
WARRANTY:
·
Genz Benz Enclosures, Inc. warrants the model 6150 & 6190 to be free from defects in materials and
workmanship for a period of 3 years from the date of purchase, when purchased from an authorized
Genz Benz dealer.
workmanship for a period of 3 years from the date of purchase, when purchased from an authorized
Genz Benz dealer.
·
This warranty does not cover normal wear and tear incurred from the normally designed use of the
product.
product.
·
This warranty is effective only if a copy of the original sales receipt is presented at the time of war-
ranty service
ranty service
·
This limited warranty is completely transferable to any subsequent buyer as long as the original sales
receipt is also transferred to such subsequent buyer.
receipt is also transferred to such subsequent buyer.
·
All warranty service must be performed by a Genz Benz authorized service center.
·
Before returning any unit for service, a returned merchandise authorization number (RMA#) must be
obtained by calling 480-941-0705.
obtained by calling 480-941-0705.