Genz-Benz td-752 ユーザーガイド
TD-752
TD-752-ES
TUBE DRIVER AMPS
FRONT PANEL FEATURES
(left to right)
TUBE DRIVE SWITCH — Selects either TUBE Channel (up), or CLEAN Channel (down). Red LED indicates Tube chan-
nel is on. Footswitch jack insertion (rear panel) cancels the operation of this switch.
CH. 1 & 2 SWITCH — When this switch is in the "up" position, both channels (Tube and Clean) may be paralleled and
will be heard together when the Tube Drive switch is set to the Tube Drive position (up). With Ch. 1 & 2 switch up and
Tube Drive switch set for Clean channel (down), only the clean channel will be heard. When Ch. 1 & 2 switch is in the
"down" position, the Tube Drive switch will select separately between Tube and Clean channels.
INPUT JACK — Extremely wide-range input allows plenty of headroom for all types of guitars.
TUBE DRIVE — Adjusts the amount of gain that drives the tube. Careful attention has been given to produce the most
overdrive/sustain possible without creating unnecessary noise and feedback.
RED LED — Indicates that the Tube Drive channel has been selected.
TUBE MASTER — Adjusts the amount of output volume from the Tube Drive Channel.
HI, MID, LO — Classic, passive 3-band E.Q. to enhance the Tube Driver's unique tonal response.
Frequencies: Hi 3.5 KHz (upper shelving)
MID 800 Hz (center)
LO 150 Hz (lower shelving)
CLEAN GAIN — Adjusts gain level of clean channel. Although this channel is all FET, extremely warm tubey tonality is
produced thanks to the MosValve power section. Lows are especially well-balanced.
HI, MID, LO — Identical operation and frequencies to Tube Drive channel, however the over-all baseline E.Q. has been
optimized for clean and rhythm styles.
REVERB — Adjusts amount of reverb signal is mixed into the output. Reverb can be cancelled anytime by the foot-
switch, or by turning the control to "0".
POWER — Supplies mains power to the amp. Be certain that the proper voltage is supplied to the amp. The proper volt-
age for your unit is indicated just below the fuse holder on the rear panel.
nel is on. Footswitch jack insertion (rear panel) cancels the operation of this switch.
CH. 1 & 2 SWITCH — When this switch is in the "up" position, both channels (Tube and Clean) may be paralleled and
will be heard together when the Tube Drive switch is set to the Tube Drive position (up). With Ch. 1 & 2 switch up and
Tube Drive switch set for Clean channel (down), only the clean channel will be heard. When Ch. 1 & 2 switch is in the
"down" position, the Tube Drive switch will select separately between Tube and Clean channels.
INPUT JACK — Extremely wide-range input allows plenty of headroom for all types of guitars.
TUBE DRIVE — Adjusts the amount of gain that drives the tube. Careful attention has been given to produce the most
overdrive/sustain possible without creating unnecessary noise and feedback.
RED LED — Indicates that the Tube Drive channel has been selected.
TUBE MASTER — Adjusts the amount of output volume from the Tube Drive Channel.
HI, MID, LO — Classic, passive 3-band E.Q. to enhance the Tube Driver's unique tonal response.
Frequencies: Hi 3.5 KHz (upper shelving)
MID 800 Hz (center)
LO 150 Hz (lower shelving)
CLEAN GAIN — Adjusts gain level of clean channel. Although this channel is all FET, extremely warm tubey tonality is
produced thanks to the MosValve power section. Lows are especially well-balanced.
HI, MID, LO — Identical operation and frequencies to Tube Drive channel, however the over-all baseline E.Q. has been
optimized for clean and rhythm styles.
REVERB — Adjusts amount of reverb signal is mixed into the output. Reverb can be cancelled anytime by the foot-
switch, or by turning the control to "0".
POWER — Supplies mains power to the amp. Be certain that the proper voltage is supplied to the amp. The proper volt-
age for your unit is indicated just below the fuse holder on the rear panel.
OWNER’S MANUAL