Dremel 231 shaper ユーザーガイド

3

Disconnect the plug from the power 
source before making any adjustments, 
changing accessories, or storing the tool. 
Such preventive safety measures reduce the 
risk of starting the tool accidentally.
Store idle tools out of reach of children 
and other untrained persons. Tools are 
dangerous in the hands of untrained users.
Maintain tools with care. Keep cutting 
tools sharp and clean. Properly maintained 
tools, with sharp cutting edges are less likely 
to bind and are easier to control. Any alteration 
or modifi cation is a misuse and may result in 
a dangerous condition.
Check for misalignment or binding of 
moving parts, breakage of parts, and 
any other condition that may affect tool 
operation. If damaged, have the tool 
serviced before using. Many accidents are 
caused by poorly maintained tools. Develop a 
periodic maintenance schedule for your tool. 

Read and understand the tool manual 
and these instructions for the use of this 
table with your router. Failure to follow all 
instructions listed below may result in serious 
personal injury.
Position the tool with the switch in “easy” 
reach so you are not blindly searching for 
it.  Power tool switches and controls need to 
be within your zone in emergency situations.
Fully assemble and tighten all the fasteners 
required for this table and mounting the 
tool. Do not use the router table until all 
assembly and installation steps have been 
completed.  Also remember to occasionally 
check the table clamps and tool to make sure 
it is still tight. A loose table is unstable and 
may shift in use and cause serious injury.
Make certain the tool is not plugged into 
a wall outlet when installing into the table, 
making adjustments or changing bits. 
Accidental start-up of the tool can cause 
injury.
Before operating make sure the entire unit 
is placed on a solid, fl at, level surface. 
Serious injury could occur if tool is unstable 
and tips.
Be certain tool is fully and securely clamped 
in the collar, periodically check the base 
fastener or clamping tightness. Adjustment

Use only accessories that are 
recommended by the manufacturer 
for your model. Accessories that may 
be suitable for one tool may become 
hazardous when used on another tool.

ed repair personnel. Service 

or maintenance performed by unqualifi ed 
personnel could result in a risk of injury. For 
example: internal wires may be misplaced or 
pinched, safety guard return springs may be 
improperly mounted.
When servicing a tool, use only identical 
replacement parts. Follow instructions in 
the Maintenance section of this manual. 
Use of unauthorized parts or failure to follow 
Maintenance Instructions may create a risk 
of electric shock or injury. Certain cleaning 
agents such as gasoline, carbon tetrachloride, 
ammonia, etc. may damage plastic parts.

devices must be securely tightened. 
Tighten as necessary as the motor can 
loosen from the base due to vibration 
and may drop or fall unexpectedly when 
positioned upside down in a table.
After changing the bits or making any 
adjustments, make sure the collet nut 
and any other adjustment devices are 
securely tightened. Loose adjustment 
devices can unexpectedly shift, causing loss 
of control, and loose rotating components 
will be violently thrown.
Do not use the router table without the 
overhead guard. The guard will aid in 
keeping your hands away from the spinning 
blade in case of unintended contact with bit.
Never place your fi ngers under the guard 
or near the spinning bit. Never hold the 
workpiece on the out-feed side of bit. 
Pressing the workpiece against the out-
feed side of the fence may cause material 
binding and possible kickback pulling your 
hand back into the bit.
Router bits are intended for wood, wood 
products and plastic only. Not for cutting 
or shaping metals. Be sure the workpiece  
does not contain nails, etc. before routing.
Cutting a nail or the like will cause the carbides