Toshiba sd-k1000 ユーザーガイド

Introduction

Note
For VCD with PBC on, you cannot select a repeat 
mode.

•  Select the items in the order you want by pressing the 

number buttons.

  Each time you press the   /   /   /   button, the space 

is highlighted in turn. Highlight where you want to enter, 
then press the corresponding number buttons.

1. OPEN/CLOSE button 
•  Press the button to open/close the disc tray.
•  The function is the same as the OPEN/CLOSE button on 

the front panel.

3. Number buttons 
  Press number buttons to play relevant chapter/track.

5. E.P.M button (Enhanced Picture Mode) 
  Use to select the picture enhancement.
 

  Select the picture enhancement by pressing   /  , then 

press   /   to make your selections.

  To exit the picture enhancement selection, press E.P.M 

again.

Note
Actual effect to picture may vary depending on the TV.  
Make selection according to your preference.

6. ANGLE button 
•  While playing a scene recorded with multiple angles, press 

the ANGLE button.

  Number changes to show the number of the current angle. 

(The maximum number of possible angles is 9)

 
  ANGLE button is also used to rotate the picture in 

clockwise direction during JPEG playback.

This function can only be used for discs on which scenes shot 
from multiple angles have been recorded. If only one angle 
is recorded, “   ” will be displayed.

7. PAUSE/STEP button 
•  Press PAUSE/STEP to freeze playback.
•  During still playback, press PAUSE/STEP advance the 

picture frame by frame.

8. SKIP button 

9. REV/FWD buttons
  REV: Fast reverse playback
  FWD: Fast forward playback
  Each time you press the REV or FWD button, the playback 

speed changes.

Display the title menu on DVD.

While playing a disc, press the PLAY MODE button 
repeatedly to select a repeat mode. 

 For 

DVD:

 

- Repeat Chapter (currently playing chapter)

 

- Repeat Title (currently playing title)

 

- Repeat All (entire disc)

 

- Off (cancel)

 

For Video CD, Audio CD:

 

- Repeat Single (currently playing track)

 

- Repeat All (entire disc)

 

- Off (cancel)

 

For MP3, JPEG:

 

- Repeat Single (currently playing fi le)

 

- Repeat Folder (current folder)

 

- Repeat All (all fi les)

 

- Off (cancel)

Use CLEAR to delete the scheduled program or to cancel 
input data in setting mode

.

Press this button, the program screen is displayed as 
below:

2. ON/STANDBY button 
  Turn the unit on or set the unit to standby mode.

1/3

e.g.   DVD

e.g.  VCD/Audio CD

To locate succeeding chapters or tracks.

To locate preceding chapters or tracks.

4. E.A.M button (Enhanced Audio Mode) 
 

Use to select the sound enhancement on or off.

 3D*:
  To obtain expansive virtual surround sound effects from 

two speakers. To use this enhancement on sounds output 
from the ANALOG AUDIO OUT jacks, be sure to set 
“Digital out” to “PCM”.

  * Effective in playback of a DVD .

•  Actual effects to sounds may vary depending on the speaker 

system. Make selection according to your preference.

•  Actual effects to sounds may vary depending on the disc.
•  When the DVD player is connected to an amplifier 

equipped with Dolby Surround Pro Logic, select “3D 
effect”. Otherwise, Dolby Surround Pro Logic may function 
differently than usual.

•  The sound effect might not be heard easily on small TVs.
•  The sound effect can be heard more easily at higher 

volume.

•  The sound effect might take a few seconds to be heard 

after turning on the E.A.M.

Use   /   /   /   to select a selection in setup menu.