Champion 64kb 仕様ガイド
90° Application
Typical Modular Configurations
Champion Industries, Inc., P. O. Box 4149, Winston-Salem, NC 27115 • 336/661-1556 • Fax: 336/661-1979 • www.championindustries.com
Warning: Plumbing and electrical
connections should be made by qualified
workmen who will observe all the applicable
plumbing, sanitary, safety codes and the
National Electrical Code.
connections should be made by qualified
workmen who will observe all the applicable
plumbing, sanitary, safety codes and the
National Electrical Code.
Note: Water Hammer Arrestor (meeting
ASSE-1010 standard or equivalent) to be
supplied (by others) in common water
supply line at service connection
ASSE-1010 standard or equivalent) to be
supplied (by others) in common water
supply line at service connection
Due to an ongoing value analysis program at
Champion, specifications contained in this
catalog are subject to change without notice.
Champion, specifications contained in this
catalog are subject to change without notice.
Available in either right-to-left,
or left-to-right operation
or left-to-right operation
For electrical, drain, and
booster connections,
consult the Factory.
booster connections,
consult the Factory.
For Options and Accessories,
refer to 64KB and 64KPRB
Specification Sheets.
refer to 64KB and 64KPRB
Specification Sheets.
Note: Machine to be installed 6" (min.)
from wall.
from wall.
180° Application
64 Modular Series
64KB and 64KPRB Corner
Multiple Tank Rack Conveyor
Modular System
Multiple Tank Rack Conveyor
Modular System
Capacities
Racks per hr. (NSF rated)
201
Wash tank (gal.)
20
Conveyor speed (ft./min.)
7
Motor horsepower
Drive
1/4
Prewash 22", 36" and 37"
1
Wash
2
Rinse
2
Water consumption
Gal. per hr. (max. use)
300
Gal. per rack
1.49
Temperature °F
Wash
150
Rinse
160
Final Rinse
180
Heating
Tank heat, electric (Kw)
25
Tank heat, steam (lbs./hr.
required at 15 psi flow pressure)
125
Electric booster (built-in)
(Kw required for 40° rise)
36
Electric booster
(Kw required for 70° rise)
57
Steam booster
(lbs./hr. required for 40° rise)
185
Steam booster
(lbs./hr. required for 70° rise)
320
Venting
Load end (minimum cfm)
200
Unload end (minimum cfm)
400
Standard 20" x 20" rack complement
Peg
2
Flat
1
Quick Facts
Standard Features
Automatic tank fill
Common utility connections
Control circuit, 115-volt
Convenient top-mounted controls
Conveyor drive 1/4-Hp motor
Door activated drain closure
Door safety switch
Enclosure panel (front)
Energy sentinel (idle pump shut-off)
External scrap basket on prewash units
Interchangeable spray arms
Leakproof doors, internally fitted
Prewash 1-Hp pump motor
Low-water tank heat protection
Rinse saver device
Stainless steel heavy gauge construction,
including base and feet
Electric tank heat
(optional: steam coil or steam injectors)
Wash and rinse pumps with 2-Hp motors
Common utility connections
Control circuit, 115-volt
Convenient top-mounted controls
Conveyor drive 1/4-Hp motor
Door activated drain closure
Door safety switch
Enclosure panel (front)
Energy sentinel (idle pump shut-off)
External scrap basket on prewash units
Interchangeable spray arms
Leakproof doors, internally fitted
Prewash 1-Hp pump motor
Low-water tank heat protection
Rinse saver device
Stainless steel heavy gauge construction,
including base and feet
Electric tank heat
(optional: steam coil or steam injectors)
Wash and rinse pumps with 2-Hp motors
®
®
*Shown on front of Spec Sheet
*Shown on front of Spec Sheet
Modular Units
Prewash 22"
A
Prewash 36"
B
Corner Prewash 39"
C
Corner Wash
D
Corner Rinse
E
Straight Wash
F
Straight Rinse
G
Wash/Rinse
H
Final Rinse Drive
J