Champion ld-20-pt 仕様ガイド
Cabinet
66" wide x 36-1/4" deep x 76-1/2" high. Overall height with door open: 99".
Door opening: 28" wide x 28-1/2" high. Constructed of 12, 14 & 16 gauge, type 304
#3 finish, STAINLESS STEEL. All seams tig-welded, cleaned and polished.
Door opening: 28" wide x 28-1/2" high. Constructed of 12, 14 & 16 gauge, type 304
#3 finish, STAINLESS STEEL. All seams tig-welded, cleaned and polished.
Door
Lift-up door type. Two doors, single control, handle. Counter balanced with self-
lubricating guides, STAINLESS STEEL cables on nylon rollers with cable guards to
insure tracking. Doors are interlocked with limit switch to prevent machine operation
while doors are open. Door construction: 16 gauge, type 304 #3 finish, STAINLESS
STEEL.
lubricating guides, STAINLESS STEEL cables on nylon rollers with cable guards to
insure tracking. Doors are interlocked with limit switch to prevent machine operation
while doors are open. Door construction: 16 gauge, type 304 #3 finish, STAINLESS
STEEL.
Recirculating Wash Tank
Heated by one 18 KW 208/240 or 480 Volt electric immersion heater, thermostatically
controlled wash temperature and low water protection system. 50 gallons, 14 gauge
STAINLESS STEEL, sloped to drain. Infrared gas and steam heating options available.
controlled wash temperature and low water protection system. 50 gallons, 14 gauge
STAINLESS STEEL, sloped to drain. Infrared gas and steam heating options available.
Wash Tank Filter
Perforated, STAINLESS STEEL basket type. Double filter system for increased
effectiveness and easy cleaning without emptying wash tank.
effectiveness and easy cleaning without emptying wash tank.
Wash Tank Fill Valve
Size 1/2" brass material, solenoid type, automatic.
Wash Tank Drain Valve
Size 1-1/4" brass material, gate type for manual or electrically operated ball valve for
automatic option.
automatic option.
Wash Pump
15 hp, 208/240 or 480 volt, 3 phase, 60 cycle. Close coupled; 250 gallons per minute
at 35 to 45 psi, mounted on 12 gauge STAINLESS STEEL formed channel base.
at 35 to 45 psi, mounted on 12 gauge STAINLESS STEEL formed channel base.
Rotating wash Hub & Spray Arm Assembly
Water driven, STAINLESS STEEL spray arm assembly with STAINLESS STEELjets,
removable end caps and hand operated quick release mechanism for easycleaning
and reassembly. Mounted on STAINLESS STEEL base.
removable end caps and hand operated quick release mechanism for easycleaning
and reassembly. Mounted on STAINLESS STEEL base.
Sanitizing Rinse Tank
STAINLESS STEEL, 10 gallon capacity, with one 12 kW 208/240 or 480 Volt electric
booster heater to provide 180°/190° F hot sanitizing rinse. Uses 4.4 gallons per
30-second cycle. Infrared gas and steam coil heating options available.
booster heater to provide 180°/190° F hot sanitizing rinse. Uses 4.4 gallons per
30-second cycle. Infrared gas and steam coil heating options available.
Rinse Supply Valve
Size 3/4" brass material, solenoid type, automatic.
Final Rinse Piping
Type 304 STAINLESS STEEL tubing with brass compression fittings and brass or
optional STAINLESS STEEL full cone rinse jets.
optional STAINLESS STEEL full cone rinse jets.
Control & Information Center
120 volt control circuit with push pad operation of “POWER ON,” “STOP” and
“SHORT, MEDIUM or LONG WASH CYCLES.” A digital display indicates “TIME
REMAINING” for each cycle. LED’s indicate wash, rinse and unload functions. A buzzer
is also included to provide an audible indication of time to unload. A pre-programmed
circuit board allows the push pad to be used as a “DIAGNOSTIC CENTER” by
displaying “ERROR CODES” for ease of troubleshooting. Moisture resistant gauges
measure Wash Temperature, Wash Pressure and Rinse Temperature.
“SHORT, MEDIUM or LONG WASH CYCLES.” A digital display indicates “TIME
REMAINING” for each cycle. LED’s indicate wash, rinse and unload functions. A buzzer
is also included to provide an audible indication of time to unload. A pre-programmed
circuit board allows the push pad to be used as a “DIAGNOSTIC CENTER” by
displaying “ERROR CODES” for ease of troubleshooting. Moisture resistant gauges
measure Wash Temperature, Wash Pressure and Rinse Temperature.
External Rinse Hose
Externally mounted rinse hose with insulated spray gun handle for easy cleaning
and maintenance of machine.
and maintenance of machine.
Steam Exhaust Vent
Steam exhaust vent 12-7/8" diameter, consisting of 14 gauge rolled STAINLESS
STEEL, collar for PVC pipe connection bolted to the top of the machine. Machine
pre-wired with control timer for the addition of a fan.
STEEL, collar for PVC pipe connection bolted to the top of the machine. Machine
pre-wired with control timer for the addition of a fan.
Champion Industries, Inc.
P. O. Box 4149, Winston-Salem, NC 27115
Tel: 336/661/1556 Fax: 336/661-1979
www.championindustries.com
2674 N. Service Road,
Jordan Station, Ontario, Canada L0R 1S0
Tel: 905/562-4195 Fax: 905/562-4618
Jordan Station, Ontario, Canada L0R 1S0
Tel: 905/562-4195 Fax: 905/562-4618
(1M) 1/06 Printed in U.S.A.
SPECIFICATIONS
MODEL LD-20-PT POT, PAN &
UTENSIL WASHER